Bedienungsanleitung Hitachi DH 36 DL (Seite 12 von 86) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

78778

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

English

Rotation only function

⅜ Drilling in steel or wood

(with optional accessories)

⅜ Tightening machine screws, wood screws

(with optional accessories)

Hammering only function (Model DH25DAL and DH36DAL

only)

⅜ Light-duty chiselling of concrete, groove digging

and edging.

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latches

to remove the battery (see Figs. 1 and 2).

CAUTION:

Never short-circuit the battery.

2. Battery installation

Insert the battery aligning both guide rail of battery

and body. Make sure the battery is fixed firmly.

CHARGING

Before using the power tool, charge the battery as follows.

1. Connect the charger’s power cord to a receptacle

When the power cord is connected, the charger’s

pilot lamp will blink in red (At 1-second intervals).

2. Insert the battery into the charger

Insert the battery firmly, until it contacts the bottom

of the charger compartment.

CAUTION

⅜ If the battery is inserted in the reverse direction,

not only recharging will become impossible, but it

may also cause problems in the charger such as

deformed recharging terminal.

3. Charging

When inserting a battery in the charger, charging

will commence and the pilot lamp will light up

continuously in red.

When the battery becomes fully recharged, the pilot

lamp will blink in red (At 1-second intervals) (See

Table 1).

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown

in Table 1, according to the condition of the charger

or the rechargeable battery.

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for

0.1 seconds. (off for 0.1 seconds)

Lights continuously

Before

charging

While

charging

Charging

complete

Charging

impossible

Overheat

standby

Blinks

(RED)

Lights

(RED)

Blinks

(RED)

Flikers

(RED)

Lights

(GREEN)

Malfunction in the battery

or the charger.

Battery overheated.

Unable to charge

(Charging will commence

when battery cools).

Table 1

Indications of the lamps

NOTE: When standby for cooling battery, UC36YRL cools the overheated battery by cooling fan.

(2) Regarding the temperatures of the rechargeable battery

The temperatures for rechargeable batteries are as

shown in the table below, and batteries that have

become hot should be cooled for a while before

being recharged.

Table 2 Recharging ranges of batteries

Charger

UC36YRL

Rechargeable batteries

BSL2530, BSL3626 0°C – 50°C

Battery type Recharging time

BSL2530 Approx. 60 min.

BSL3626 Approx. 80 min.

(3) Regarding recharging time

Depending on the type of the battery, the charging

time will decome as shown in Table 3.

Table 3 Charging time (At 20°C)

NOTE: The charging time may vary according to ambient

temperature and power source voltage.

4. Disconnect the charger’s power cord from the

receptacle

01Eng_DH25DL_WE 08/4/30, 09:3311

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DH 36 DL Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info