Bedienungsanleitung Hitachi DH18DSL (Seite 16 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566482

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

English

(2) Tightening wood screws

Prior to tightening wood screws, make pilot holes

suitable for them in the wooden board. Apply the

bit to the screw head grooves and gently drive the

screws in the holes.

CAUTION

Exercise care in preparing a pilot hole suitable for

the wood screw taking the hardness of the wood

into consideration. Should the hole be excessively

small or shallow, requiring much power to drive

the screw into it, the thread of the wood screw may

sometimes be damaged.

5. Using depth gauge (Fig. 14)

(1) Loosen the knob on the side handle, and insert the

depth gauge into the mounting hole on the side

handle.

(2) Adjust the depth gauge position according to the

depth of the hole and tighten the knob bolt securely.

6. How to use the drill bit (taper shank) and the taper

shank adapter

(1) Mount the taper shank adapter to the rotary hammer.

(Fig. 15)

(2) Mount the drill bit (taper shank) to the taper shank

adapter. (Fig. 15)

(3) Turn the switch ON, and drill a hole to prescribed

depth.

(4) To remove the drill bit (taper shank), insert the

cotter into the slot of the taper shank adapter and

strike the head of the cotter with a hammer

supporting on the rest. (Fig. 16)

7. Switching between the “SAVE“ and the “POWER“

modes

The hammering force of the hammer can be

increased or decreased to conform with intended

usage, by operating the shift knob as per Fig. 17.

Adjust the force to match the usage intended.

(1) “SAVE“ mode ... decreased hammering force

This can prevent thin drill bits which are less than

4.3 mm in diameter, from being bent or broken.

(2) “POWER“ mode ... increased hammering force

⅜ This can be used to speedily and efficiently drill

holes when the drill bits which are being used are

greater than 4 mm in diameter.

⅜ This can be used to drill holes into wood or metal.

CAUTION

Do not drill holes in wood with the “SAVE“ mode.

There is a likelihood that the motor will burn out

because it can easily lock up due to the low power.

8. About Remaining Battery Indicator

When pressing the remaining battery indicator

switch, the remaining battery indicator lamp lights

and the battery remaining power can be checked.

(Fig. 18) When releasing your finger from the

remaining battery indicator switch, the remaining

battery indicator lamp goes off. The Table 5 shows

the state of remaining battery indicator lamp and

the battery remaining power.

As the remaining battery indicator shows somewhat

differently depending on ambient temperature and

battery characteristics, read it as a reference.

NOTE:

⅜ Do not give a strong shock to the switch panel or

break it.It may lead to a trouble.

⅜ To save the battery power consumption, the

remaining battery indicator lamp lights while

pressing the remaining battery indicator switch.

9. How to use the LED light

Every time you press the light switch on the

switch panel, the LED light lights or goes off.

(Fig. 19)

To prevent the battery power consumption, turn

off the LED light frequently.

CAUTION

⅜ Do not expose directly your eye to the light by

looking into the light.

If your eye is continuously exposed to the light,

your eye will be hurt.

NOTE:

⅜ To prevent the battery power consumption caused

by forgetting to turn off the LED light, the light goes

off automatically in about 15 minutes.

LUBRICATION

Low viscosity grease is applied to this rotary hammer so

that it can be used for a long period without replacing the

grease. Please contact the nearest service center for

grease replacement when any grease is leaking form

loosened screw.

Further use of the rotary hammer despite the grease

shortage causes damage to reduce the service life.

CAUTION

A specific grease (FG-6A) is used with this machine,

therefore, the normal performance of the machine may

be badly affected by use of different grease. Please be

sure to let one of our service centers to undertake

replacement of the grease.

State of lamp Battery Remaining Power

The battery remaining power

is enough.

The battery remaining power

is a half.

The battery remaining power

is nearly empty.

Re-charge the battery soonest

possible.

Table 5

01Eng_DH14DSL_WE 08/3/20, 20:1615

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DH18DSL Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info