Bedienungsanleitung Hitachi DH24DVCS (Seite 13 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566490

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

English

(2) Regarding the temperatures of the rechargeable

battery.

The temperatures for rechargeable batteries are as

shown in the table 2, and batteries that have become

hot should be cooled for a while before being

recharged.

Table 2

(3) Regarding recharging time

Depending on the type of the battery, the charging

time will become as shown in Table 3.

Table 3 Charging time (At 20°C)

NOTE: The charging time may vary according to ambient

temperature and power source voltage.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger firmly and pull out the battery.

NOTE

After operation, pull out batteries from the charger

first, and then keep the batteries properly.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries and

batteries that have not been used for an extended period

is not activated, the electric discharge might be low when

using them the first and second time. This is a temporary

phenomenon, and normal time required for recharging

will be restored by recharging the batteries 2–3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the

electric current, the battery may be damaged and

its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a

while.

CAUTION

⅜ If the battery is charged while it is heated because

it has been left for a long time in a location subject

to direct sunlight or because the battery has just

been used, the pilot lamp of the charger lights for

1 second, does not light for 0.5 seconds (off for

0.5 seconds). In such a case, first let the battery

cool, then start charging.

⅜ Since the built-in micro computer takes about 3

seconds to confirm that the battery being charged

with UC24SGH is taken out, wait for a minimum

of 3 seconds before reinserting it to continue

charging. If the battery is reinserted within 3 seconds,

the battery may not be properly charged.

PRIOR TO OPERATION

1. Mounting the drill bit (Fig. 4, 5)

CAUTION

To prevent accidents, make sure to turn the switch

off.

NOTE

When using tools such as drill bits, etc., make sure

to use the genuine parts designated by our company.

(1) Clean the shank portion of the drill bit.

(2) Insert the drill bit in a twisting manner into the tool

holder until it latches itself. (Fig. 4)

(3) Check the latching by pulling on the drill bit.

(4) To remove the drill bit, fully pull the grip in the

direction of the arrow and pull out the drill bit.

2. Confirm that the battery is mounted correctly.

3. Installation of dust cup or dust collector (B) (Optional

accessories) (Fig. 6, Fig. 7)

When using a rotary hammer for upward drilling

operations attach a dust cup or a dust collector (B)

to collect dust or particles for easy operation.

⅜ Installing the dust cup

Use the dust cup by attaching to the drill bit as

shown in Fig. 6.

When using a bit which has big diameter, enlarge

the center hole of the dust cup with this rotary hammer.

Battery type Recharging time

BSH2420 Approx. 60 min.

Temperatures at

Battery type which the battery

can be recharged

BSH2420 0°C – 50°C

Table 1

Indications of the pilot lamp

Before Blinks Lights for 0.5 seconds. Does not light

charging for 0.5 seconds. (off for 0.5 seconds)

Lights Lights continuously

Blinks Lights for 0.5 seconds. Does not light

for 0.5 seconds. (off for 0.5 seconds)

Blinks Lights for 1 second. Does not light

for 0.5 seconds. (off for 0.5 seconds)

Overheat

standby

While

charging

Charging

complete

Battery overheated.

Unable to charge.

(Charging will

commence when

battery cools)

Pilot lamp

(red)

01Eng_DH24DVC(S)_WE 4/17/12, 9:2312

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DH24DVCS Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info