Bedienungsanleitung Hitachi DH24PB-2 (Seite 11 von 82) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566492

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

English

APPLICATIONS

Rotation and striking function

⅜ Drilling anchor holes

⅜ Drilling holes in concrete

⅜ Drilling holes in tile

Rotation only function

⅜ Drilling in steel or wood

(with optional accessories)

⅜ Tightening machine screws, wood screws

(with optional accessories)

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a power receptacle while

the power switch is in the ON position, the power

tool will start operating immediately, which could

cause a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Mounting the drill bit (Fig. 1)

(1) To attach a drill bit (SDS-plus shank), fully pull the

grip in the direction of the arrow as shown in Fig. 1

and insert the drill bit as far as it will go while manually

turning.

(2) By releasing the grip, the drill bit will be secured.

(3) To remove the drill bit, fully pull the grip in the

direction of the arrow and pull out the drill bit.

5. Installation of dust cup or dust collector (B)

(Optional accessories) (Fig. 2, Fig. 3)

When using a rotary hammer for upward drilling

operations attach a dust cup or dust collector (B) to

collect dust or particles for easy operation.

⅜ Installing the dust cup

Use the dust cup by attaching to the drill bit as shown

in Fig. 2.

When using a bit which has big diameter, enlarge the

center hole of the dust cup with this rotary hammer.

⅜ Installing dust collector (B)

When using dust collector (B), insert dust collector

(B) from the tip of the bit by aligning it to the groove

on the grip. (Fig. 3)

CAUTION:

⅜ The dust cup and dust collector (B) are for exclusive

use of concrete drilling work. Do not use them for

wood or metal drilling work.

⅜ Insert dust collector (B) completely into the chuck

part of the main unit.

⅜ When turning the rotary hammer on while dust

collector (B) is detached from a concrete surface,

dust collector (B) will rotate together with the drill bit.

Make sure to turn on the switch after pressing the

dust cup on the concrete surface. (When using dust

collector (B) attached to a drill bit that has more than

190 mm of overall length, dust collector (B) cannot

touch the concrete surface and will rotate. Therefore

please use dust collector (B) by attaching to drill bits

which have 166 mm, 160 mm, and 110 mm overall

length.)

⅜ Dump particles after every two or three holes when

drilling.

⅜ Please replace the drill bit after removing dust

collector (B).

6. Selecting the driver bit

Screw heads or bits will be damaged unless a bit

appropriate for the screw diameter is employed to

drive in the screws.

7. Confirm the direction of bit rotation (Fig. 4)

The bit rotates clociwise (viewed from the rear side)

by pushing the R-side of the reversing switch lever.

The L-side of the lever is pushed to turn the bit

counterclockwise.

HOW TO USE

CAUTION:

To prevent accidents, make sure to turn the switch

off and disconnect the plug from the receptacle when

the drill pits and other various parts are installed or

removed. The power switch should also be turned

off during a work break and after work.

1. Switch operation

(1) DH24PA

By pulling the trigger switch and depressing the

stopper, the switch is held in the ON position for

continuous operation. To turn the drill OFF, pull the

trigger switch again and release.

(2) DH24PB

The rotation speed of the drill bit can be controlled

steplessly by varying the amount that the trigger

switch is pulled. Speed is low when the trigger

switch is pulled slightly and increases as the switch

is pulled more. Continuous operation may be attained

by pulling the trigger switch and depressing the

stopper. To turn the switch OFF, pull the trigger

switch again to disengage the stopper, and release

the trigger switch to its original position.

2. Rotation + striking

This rotary hammer can be set to rotation and striking

mode by turning the change lever fully

counterclockwise to the

mark. (Fig. 5)

(1) Mount the drill bit.

(2) Pull the trigger switch after applying the drill bit tip to

the drilling position. (Fig. 6)

(3) Pushing the rotary hammer forcibly is not necessary

at all. Pushing slightly so that drill dust comes out

gradually is sufficient.

CAUTION:

When the drill bit touches construction iron bar, the

bit will stop immediately and the rotary hammer will

react to revolve. Therefore grip the side handle and

handle tightly as shown in Fig. 6.

3. Rotation only

The hammer drill can be set to rotation only mode by

rotating the change lever fully clockwise to the

mark. (Fig. 7)

To drill wood or metal material using the drill chuck

and chuck adapter (optional accessories), proceed as

follows.

Installing drill chuck and chuck adapter: (Fig. 8)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DH24PB-2 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi DH24PB-2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info