Bedienungsanleitung Hitachi DH24PG (Seite 12 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566498

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

English

APPLICATIONS

Rotation and hammering function

⅜ Drilling anchor holes

⅜ Drilling holes in concrete

⅜ Drilling holes in tile

Rotation only function

⅜ Drilling in steel or wood

(with optional accessories)

⅜ Tightening machine screws, wood screws

(with optional accessories)

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position. If

the plug is connected to a power receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause a

serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Mounting the drill bit (Fig. 1)

CAUTION

To prevent accidents, make sure to turn the switch

off and disconnect the plug from the receptacle.

NOTE

When using tools such as bull points, drill bits, etc.,

make sure to use the genuine parts designated by

our company.

(1) Clean the shank portion of the drill bit.

(2) Insert the drill bit in a twisting manner into the tool

holder until it latches itself (Fig. 1).

(3) Check the latching by pulling on the drill bit.

(4) To remove the drill bit, fully pull the grip in the

direction of the arrow and pull out the drill bit (Fig. 2).

5. Installation of dust cup or dust collector (B)

(Optional accessories) (Fig. 3, Fig. 4)

When using a rotary hammer for upward drilling

operations attach a dust cup or dust collector (B) to

collect dust or particles for easy operation.

⅜ Installing the dust cup

Use the dust cup by attaching to the drill bit as shown

in Fig. 3.

When using a bit which has big diameter, enlarge the

center hole of the dust cup with this rotary hammer.

⅜ Installing dust collector (B)

When using dust collector (B), insert dust collector

(B) from the tip of the bit by aligning it to the groove

on the grip (Fig. 4).

CAUTION

⅜ The dust cup and dust collector (B) are for exclusive

use of concrete drilling work. Do not use them for

wood or metal drilling work.

⅜ Insert dust collector (B) completely into the chuck

part of the main unit.

⅜ When turning the rotary hammer on while dust

collector (B) is detached from a concrete surface,

dust collector (B) will rotate together with the drill bit.

Make sure to turn on the switch after pressing the

dust cup on the concrete surface. (When using dust

collector (B) attached to a drill bit that has more than

190 mm of overall length, dust collector (B) cannot

touch the concrete surface and will rotate. Therefore

please use dust collector (B) by attaching to drill bits

which have 166 mm, 160 mm, and 110 mm overall

length.)

⅜ Dump particles after every two or three holes when

drilling.

⅜ Please replace the drill bit after removing dust

collector (B).

6. Selecting the driver bit

Screw heads or bits will be damaged unless a bit

appropriate for the screw diameter is employed to

drive in the screws.

7. Confirm the direction of bit rotation (Fig. 5)

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the push button.

The L-side of the push button is pushed to turn the bit

counterclockwise.

HOW TO USE

CAUTION

To prevent accidents, make sure to turn the switch

off and disconnect the plug from the receptacle when

the drill bits and other various parts are installed or

removed. The power switch should also be turned

off during a work break and after work.

1. Switch operation

The rotation speed of the drill bit can be controlled

steplessly by varying the amount that the trigger

switch is pulled. Speed is low when the trigger switch

is pulled slightly and increases as the switch is pulled

more. Continuous operation may be attained by

pulling the trigger switch and depressing the stopper.

To turn the switch OFF, pull the trigger switch again

to disengage the stopper, and release the trigger

switch to its original position.

However, the switch trigger can only be pulled in

halfway during reverse and rotates at half the speed

of forward operation.

The switch stopper is unusable during reverse.

2. Rotation + hammering

This rotary hammer can be set to rotation and

hammering mode by pressing the push button and

turning the change lever to the

mark (Fig. 6).

(1) Mount the drill bit.

(2) Pull the trigger switch after applying the drill bit tip to

the drilling position (Fig. 7).

(3) Pushing the rotary hammer forcibly is not necessary

at all. Pushing slightly so that drill dust comes out

gradually is sufficient.

CAUTION

When the drill bit touches construction iron bar, the

bit will stop immediately and the rotary hammer will

react to revolve. Therefore grip the side handle and

handle tightly as shown in Fig. 7.

01Eng_DH24PG_26PB_WE 4/8/13, 10:5612

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DH24PG Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info