Bedienungsanleitung Hitachi DL18DMRA (Seite 17 von 108) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566301

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

English

Table 3

* Use an adapter for a small diameter bit.

These data are for the referential values. The number of

holes that can be drilled varies according to the sharpness

of the used bit or the conditions of the concrete being

drilled.

CAUTION:

When using this unit continuously, the unit may

overheat, leading to damage in the motor and switch.

Please leave it without using it for approximately

15 minutes.

HOW TO USE

CAUTION:

⅜ When using the light equipped hook, pay sufficient

attention so that the main equipment does not fall.

If the tool falls, there is a risk of accident.

⅜ Do not attach the tip tool except phillips bit to the

tool main unit when carrying the tool main unit with

the light equipped hook suspended from a waist

belt.

Injury may result if you carry the equipment

suspended from the waist belt with sharp tipped

components such as drill bit attached.

1. Using the light equipped hook

The light equipped hook can be installed on the

right or left side and the angle can be adjusted in

5 steps between 0° and 80°.

(1) Operating the hook

(a) Pull out the hook toward you in the direction

of arrow (A) and turn in the direction of arrow

(B). (Fig. 9)

(b) The angle can be adjusted in 5 steps (0°, 20°,

40°, 60°, 80°).

Adjust the angle of the hook to the desired

position for use.

(2) Switching the hook position

CAUTION:

Incomplete installation of the hook may result in

bodily injury when used.

(a) Securely hold the main unit and remove the

screw using a slotted head screwdriver or a

coin. (Fig. 10)

(b) Remove the hook and spring. (Fig. 11)

securely fasten with screw. (Fig. 12)

2. Confirm that the battery is mounted correctly.

3. Installation of dust cup or dust collector (B) (Optional

accessories) (Fig. 6, Fig. 7)

When using a rotary hammer for upward drilling

operations attach a dust cup or a dust collector (B)

to collect dust or particles for easy operation.

⅜ Installing the dust cup

Use the dust cup by attaching to the drill bit as

shown in Fig. 6.

When using a bit which has big diameter, enlarge

the center hole of the dust cup with this rotary

hammer.

⅜ Installing dust collector (B)

When using dust collector (B), insert dust collector

(B) from the tip of the bit by aligning it to the

groove on the grip. (Fig. 7)

CAUTION:

⅜ The dust cup and dust collector (B) are for exclusive

use of concrete drilling work. Do not use them for

wood or metal drilling work.

⅜ Insert dust collector (B) completely into the chuck

part of the main unit.

⅜ When turning the rotary hammer on while dust

collector (B) is detached from a concrete surface,

dust collector (B) will rotate together with the drill

bit. Make sure to turn on the switch after pressing

dust cup on the concrete surface. When using dust

collector (B) attached to a drill bit that has more

than 190 mm of overall length, dust collector (B)

cannot touch the concrete surface and will rotate.

Therefore, please use dust collector (B) by attaching

to drill bits which have 166 mm, 160 mm, and 110

mm overall length.

⅜ Dump particles after every two or three holes when

drilling.

⅜ Please replace the drill bit after removing dust

collector (B).

4. Selecting the driver bit

Screw heads or bits will be damaged unless a bit

appropriate for the screw diameter is employed to

drive in the screws.

5. Confirm the direction of bit rotation (Fig. 8)

The bit rotates clockwise (viewed from the rear

side) by pushing the R-side of the push button.

The L-side of the push button is pushed to turn the

bit counterclockwise. (See Fig. 8) (The

and

marks are provided on the body.)

CAUTION:

The push button cannot be switched while the

power tool is turning. To switch the push button,

stop the power tool, then set the push button.

6. Continuous drilling

The number of holes that can be drilled in concrete

after one recharge is shown in Table 3.

Possible continuous

Bit dia. Depth

drilling number (holes)

(mm) (mm) DH14DL DH18DL DH14DMR DH18DMR

3.0 Ah battery 2.0 Ah battery

*3.5 65 110 43 73

498122 65 81

580113 53 75

63072105 48 70

855773751

10 48 64 32 43

12 41 57 27 38

14 34 47 23 31

16 22 32 15 21

01Eng_DH14DL_WE 11/6/08, 20:2816

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DL18DMRA Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info