Bedienungsanleitung Hitachi ds 10 dfl (Seite 11 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

389128

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

English

CAUTION

⅜ The selection examples shown in Table 5 should be

considered as general standard. As different types of

tightening screws and different materials to be

tightened are used in actual works proper adjustments

are naturally necessary.

⅜ When using the driver drill with a machine screw at

HIGH (high speed), a screw may damage or a bit may

loose due to the tightening torque is too strong. Use

the driver drill at LOW (low speed) when using a

machine screw.

NOTE

The use of the battery BCL1015 or BCL1030M in a

cold condition (below 0 degree Centigrade) can

sometimes result in the weakened tightening torque

and reduced amount of work. This, however, is a

temporary phenomenon, and returns to normal when

the battery warms up.

6. Mounting and dismounting of the bit

(1) Mounting the bit

After inserting a driver bit, etc. into the keyless drill

chuck, firmly grasp the ring and tighten the sleeve by

turning it toward the right (in the clockwise direction

as viewed from the front) (See Fig. 10).

⅜ If the sleeve becomes loose during operation, tighten

it further. The tightening force becomes stronger

when the sleeve is tightened additionally.

(2) Dismounting the bit

Firmly grasp the ring and loosen the sleeve by turning

it toward the left (in the counter-clockwise direction

as viewed from the front) (See Fig. 10).

CAUTION

When it is no longer possible to loosen the sleeve, use a

vise or similar instrument to secure the bit. Set the

clutch mode between 1 and 13, and then turn the

sleeve to the loose side (left side) while operating the

clutch. It should be easy now to loosen the sleeve.

7. Confirm that the battery is mounted correctly

8. Check the rotational direction

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn the

bit counterclockwise (See Fig. 6) (The

and

marks are provided on the body).

9. Switch operation

⅜ When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

⅜ The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled.

Speed is low when the trigger switch is pulled slightly

and increases as the trigger switch is pulled more.

NOTE

A buzzing noise is produced when the motor is about

to rotate; This is only a noise, not a machine failure.

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade efficiency and

cause possible motor malfunction, sharpen or replace

the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Cleaning on the outside

When the driver drill is stained, wipe with a soft dry

cloth or a cloth moistened with soapy water. Do not

use chloric solvents, gasoline or paint thinner, for

they melt plastics.

5. Storage

Store the driver drill in a place in which the

temperature is less than 40°C and out of reach of

children.

NOTE

Make sure that the battery is fully charged when

stored for a long period (3 months or more). The

battery with smaller capacity may not be able to be

charged when used, if stored for a long period.

6. Service parts list

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

5. How to select tightening torque and rotational speed

Table 5

Use

Clutch Dial

Rotating speed selection (Position of the shift knob)

Position

LOW (Low speed) HIGH (High speed)

Machine screw 1 – 21

For 4 mm or smaller diameter

screws.

Driving

Wood screw

1 –

For 5.8 mm or smaller nominal

diameter screws.

Wood

For 21 mm or smaller

diameters.

Driling

Metal

For drilling with a metal

working drill bit.

For 6 mm or smaller

diameter screws.

For 3.8 mm or smaller

nominal diameter screws.

For 12 mm or smaller

diameters.

01Eng_DS10DFL_WE 6/21/11, 8:5510

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi ds 10 dfl Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info