Bedienungsanleitung Hitachi DS 12 DVB 2 (Seite 13 von 90) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

78456

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

English

⅜ When setting the shift knob to “HIGH” (high speed)

and the position of the cap is “17” or “22”, it may

happen that the clutch does not engaged and that

the motor is locked. In such a case, please set the

shift knob to “LOW” (low speed).

Work Suggestions

Wood

Drilling Steel Use for drilling purpose.

Aluminum

Machine screw Use the bit or socket matching the screw diameter.

Driving

Wood screw Use after drilling a pilot hole.

Table 6

Use Cap Position

Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Machine screw 1 – 22

For 4 mm or smaller diameter

screws.

Driving

Wood screw 1 –

For 8 mm or smaller nominal

diameter screws. (DS18DVB2/

DS14DVB2/DS12DVB2)

For 5.5 mm or smaller nominal

diameter screws. (DS9DVB2)

Wood

For 38 mm or smaller

diameters. (DS18DVB2)

For 36 mm or smaller

diameters. (DS14DVB2)

Drilling

For 32 mm or smaller

diameters. (DS12DVB2)

For 21 mm or smaller

diameters. (DS9DVB2)

Metal

For drilling with a metal

working drill bit.

For 6 mm or smaller

diameter screws.

For 4.8 mm or smaller

nominal diameter screws.

For 24 mm or smaller

diameters. (DS18DVB2)

For 18 mm or smaller

diameters. (DS14DVB2/

DS12DVB2/DS9DVB2)

CAUTION:

⅜ The selection examples shown in Table 7 should

be considered as general standard. As different

types of tightening screws and different materials

to be tightened are used in actual works proper

adjustments are naturally necessary.

⅜ When using the driver drill with a machine screw

at HIGH (high speed), a screw may damage or a

bit may loose due to the tightning torque is too

strong. Use the driver drill at LOW (low speed)

when using a machine screw.

NOTE:

The use of the battery EB9H, EB926H, EB930H,

EB1222HL, EB1226HL, EB1230HL, EB1426H, EB1430H,

EB1826HL and EB1830HL in a cold condition (below

0 degree Centigrade) can sometimes result in the

weakened tightening torque and reduced amount

of work. This, however, is a temporary phenomenon,

and returns to normal when the battery warms up.

6. Mounting and dismounting of the bit

(1) Mounting the bit

Loosen the sleeve by turning it toward the left (in

the counterclockwise direction as viewed from the

front) to open the clip on the keyless chuck. After

inserting a driver bit, etc., into the keyless drill

chuck, and tighten the sleeve by turning it toward

the right (in the clockwise direction as viewed from

the front) (See Fig. 10).

⅜ If the sleeve becomes loose during operation, tighten

it further.

The tightening force becomes stronger when the

sleeve is tightened additionally.

(2) Dismounting the bit

Loosen the sleeve by turning it toward the left (in

the counterclockwise direction as viewed from the

front), and then take out the bit ect (See Fig. 10).

⅜ If the motor is locked, immediately turn the power

off. If the motor is locked for a while, the motor

or battery may be burnt.

4. The scope and suggestions for uses

The usable scope for various types of work based on the mechanical structure of this unit is shown in

Table 6.

5. How to select tightening torque and rotational speed

Table 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DS 12 DVB 2 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi DS 12 DVB 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info