Bedienungsanleitung Hitachi DS 12 DVF 3 (Seite 12 von 108) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

78142

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

English

4. Battery (EB1814SL, BCC1815, EB1820L, BCH1820)

(For DS18DVF3)

Optional accessories are subject to change without notice.

APPLICATIONS

○ Driving and removing of machine screws, wood screws,

tapping screws, etc.

○ Drilling of various metals.

○ Drilling of various woods.

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latch (1 pc.

or 2 pcs.) to remove the battery (see Figs. 1 and 2).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 2).

CHARGING

Before using the driver drill, charge the battery as follows.

1. Insert the battery into the charger

Insert the battery ﬁ rmly while observing its direction, until

it contacts the bottom of the charger (See Fig. 3).

CAUTION

The UC9SD and UC12SD models are the exclusively

designed charger. These cannot charge batteries

except the speciﬁ ed batteries. It is possible to insert

the batteries other than the speciﬁ ed into the charger

and some of them may light up the pilot lamps.

However, you are requested to exercise utmost

caution not to charge batteries other than speciﬁ ed

ones because these can not

only be charged but

also such actions can result in the malfunction of

chargers.

2. Connect the charger power cord to the receptacle.

Connecting the power cord will turn on the charger (the

pilot lamp lights up).

CAUTION

If the pilot lamp does not light up, pull out the power

cord from

the receptacle and check the battery

mounting condition.

About 60 minutes are required to fully charge the battery

at a temperature of about 20°C. The pilot lamp goes oﬀ to

indicate that the battery is fully charged.

The battery charging time becomes longer when a

temperature is low or the

voltage of the power source is

too low.

When the pilot lamp does not go oﬀ even if more than 120

minutes have elapsed after starting of the charging, stop

the charging and contact your HITACHI AUTHORIZED

SERVICE CENTER.

CAUTION

If the battery is heated due to direct sunlight, etc.,

just after operation, the charger pilot lamp may not

light up. At that time, cool the battery ﬁ rst, then start

charging.

3. Disconnect the charger power cord from the

receptacle

4. Hold the charger ﬁ rmly and pull out the battery

NOTE

After charging, pull out batteries from the charger ﬁ rst,

and then

keep the batteries properly.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries and

batteries that have not been used for an extended period

is not activated, the electric discharge might be low when

using them the ﬁ rst and second time. This is a temporary

phenomenon, and

normal time required for recharging

will be restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery. If

you continue to use the tool and exhaust the electric

current, the battery may be

damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use.

If such a battery is recharged immediately after use, its

internal chemical substance will deteriorate, and the

battery life will be shortened. Leave the battery and

recharge it after

it has cooled for a while.

Before using the driver drill, charge the battery as follows.

1. Connect the charger power cord to the receptacle

Connecting the power cord will turn on the charger.

2. Insert the battery into the charger

Insert the battery ﬁ rmly while observing its direction,

until it contacts

the bottom of the charger (See

Fig. 4) (the pilot lamp lights up).

CAUTION

If the pilot lamp does not light up, pull out the power

cord from the receptacle and check the battery

mounting condition.

(1) Regarding the temperatures of the rechargeable battery

The temperatures for rechargeable batteries are as

shown

in Table 1.

Table 1 Recharging ranges of batteries

Rechargeable batteries

Temperatures at

which the battery

can be recharged

EB912S, EB914S, BCC915,

EB9B, EB1212S, EB1214S,

BCC1215, EB1220BL,

EB1412S, EB1414S,

BCC1415, EB14B,

EB1814SL, BCC1815,

EB1820L

0°C – 45°C

(2) Regarding recharging time

Depending on the combination of the charger and

batteries, the charging time will become as shown in

Table 2.

000Book_DS9DVF3_WETha.indb 12000Book_DS9DVF3_WETha.indb 12 2012/06/06 8:46:142012/06/06 8:46:14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DS 12 DVF 3 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi DS 12 DVF 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info