Bedienungsanleitung Hitachi DS 12 DVF 3 (Seite 16 von 108) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

78142

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

English

8. Check the rotational direction

The bit rotates clockwise (viewed from the rear side) by

pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn the bit

counterclockwise (See Fig. 11) (The

and

marks

are provided on the body).

9. Switch operation

○ When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

○ The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled.

Speed is low when the

trigger switch is pulled slightly and

increases as the trigger switch is pulled more.

NOTE

A buzzing noise is produced when the motor is about to

rotate; This is only a noise, not a machine failure.

10. Using the hook

CAUTION

○ When using the hook, pay suﬃ cient attention so that the

main equipment does not fall. If the tool falls, there is a

risk of accident.

○ Do not attach the tip tool except phillips bit to the tool

main unit when carrying the tool main unit with the hook

suspended from a waist belt.

Injury may result if you carry the

equipment suspended

from the waist belt with sharp tipped components such

as drill bit attached.

The hook can be installed on the right or left side and the

angle can be adjusted in 5 steps between 0° and 80°.

(1) Operating the hook

(a) Pull out the hook toward you in the

direction of arrow

(A) and turn in the direction of arrow (B) (Fig. 12).

(b) The angle can be adjusted in 5 steps (0°, 20°, 40°,

60°, 80°).

Adjust the angle of the hook to the desired position for

use.

(2) Switching the hook position

CAUTION

Incomplete installation of the hook

may result in bodily

injury when used.

(a) Securely hold the main unit and remove the screw

using a slotted head screwdriver or a coin (Fig. 13).

(b) Remove the hook and spring (Fig. 14).

securely fasten with screw

(Fig. 15).

NOTE

Pay attention to the spring orientation. Install the spring

with larger diameter away from you (Fig. 15).

(3) Using the bit holder (Hook with bit holder)

○ Installing the bit

Slide the bit from the side and then insert ﬁ rmly until

the groove on the bit locks in

the protruded section of

the hook.

○ Removing the bit

Securely hold the main unit and pull out the bit by

holding the tip with your thumb (Fig. 16).

CAUTION

Only Hitachi STANDARD ACCESSORIES phillips bit

(No. 2 × 65L; Code No. 983006) may be used. Do not

use other bits

since they may come loose.

(4) Using as an auxiliary light (Hook with light)

(a) Press the switch to turn oﬀ the light.

If forgotten, the light will turn oﬀ automatically after 15

minutes.

(b) The direction of the light can be adjusted within the

range of hook positions 1 -

5 (Fig. 17).

○ Lighting time

AAAA manganese batteries: approx. 15 hrs.

AAAA alkali batteries: approx. 30 hrs.

CAUTION

Do not look directly into the light.

Such actions could result in eye injury.

(5) Replacing the batteries

(a) Loosen the hook screw with a phillips-head

screwdriver (No. 1) (Fig. 18).

Remove the hook cover by pushing in the direction of

the arrow (Fig. 19).

(b) Remove the old

batteries and insert the new batteries.

Align with the hook indications and position the plus

(+) and minus (–) terminals correctly (Fig. 20).

protuberance of the hook cover, press the hook cover

in the direction opposite to that of

the arrow shown in

Fig. 19 and then tighten the screw.

Use commercially available AAAA batteries

(1.5 V).

NOTE

Do not tighten the screw excessively. Such action could

strip the screw threads.

CAUTION

○ Failure to observe the following can result in battery

leakage, rust or malfunction.

Position the plus (+) and minus

(–) terminals correctly.

Replace both batteries at the same time. Do not mix old

and new batteries.

Remove exhausted batteries from the hook immediately.

○ Do not discard batteries together with normal trash and

do not throw batteries into ﬁ re.

○ Store batteries out of the reach of children.

○ Use batteries

correctly in accordance with the battery

speciﬁ cations and indications.

11. Using the bit holder

CAUTION

○ Stow the bit in the speciﬁ ed location on the tool. If the tool

is used with the bit stowed improperly, the bit may fall and

cause bodily injury.

○ Do not stow bits that are

of a diﬀ erent length, gauge or

dimension than the plus driver bit (65 mm long) included

in the STANDARD ACCESSORIES.

The bit may fall and cause bodily injury.

(1) Removing the bit

Securely hold the main unit and pull out the bit by holding

the tip with your thumb (

Fig. 21).

(2) Installing the Bit

Install the bit with steps opposite of when removing.

Insert the bit so that the right and left sides are equal, as

shown in Fig. 22

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade eﬃ ciency and cause

possible motor malfunction, sharpen or replace the tool

as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the

screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Cleaning on the outside

When the driver drill is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt

plastics.

4. Storage

Store the driver drill in a place in which the temperature is

less than 40°C and out of reach of children.

000Book_DS9DVF3_WETha.indb 16000Book_DS9DVF3_WETha.indb 16 2012/06/06 8:46:152012/06/06 8:46:15

Hitachi DS 12 DVF 3 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi DS 12 DVF 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info