Bedienungsanleitung Hitachi DS 14 DL (Seite 11 von 98) (Deutsch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

78236

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

English

APPLICATIONS

⅜ Driving and removing of machine screws, wood

screws, tapping screws, etc.

⅜ Drilling of various metals

⅜ Drilling of various woods

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latch (2

pcs.) to remove the battery (see Figs. 1 and 2).

CAUTION:

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (see

Fig. 2).

CHARGING

〈

UC18YRL

〉

Before using the driver drill, charge the battery as follows.

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charger’s

pilot lamp will blink in red. (At 1-second intervals)

2. Insert the battery into the charger.

Firmly insert the battery into the charger till it contacts

the bottom of the charger and checking the polarities

as shown in Fig. 3.

CAUTION:

⅜ If the batteries are inserted in the reverse direction,

not only recharging will become impossible, but it

may also cause problems in the charger such as a

deformed recharging terminal.

3. Charging

When inserting a battery in the charger, charging will

commence and the pilot lamp will light continuously

in red.

When the battery becomes fully recharged, the pilot

lamp will blink in red. (At 1-second intervals) (See

Table 1)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown in

Table 1, according to the condition of the charger or

the rechargeable battery.

(2) Regarding the temperatures of the rechargeable

battery

The temperatures for rechargeable batteries are as

shown in Table 2, and batteries that have become

hot should be cooled for a while before being

recharged.

Table 2 Recharging ranges of batteries

(3) Regarding recharging time

Depending on the combination of the charger and

batteries, the charging time will become as shown

in Table 3.

Table 3 Charging time (At 20°C)

NOTE:

The charging time may vary according to temperature

and power source voltage.

Lights for 0.5 seconds. Does not light for 0.5

seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for 0.5

seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for 0.1

seconds. (off for 0.1 seconds)

Lights continuously

Before

charging

While

charging

Charging

complete

Charging

impossible

Blinks

(RED)

Lights

(RED)

Blinks

(RED)

Flickers

(RED)

Lights

(GREEN)

Malfunction in the battery

or the charger

Battery overheated.

Unable to charge.

(Charging will commence

when battery cools)

Table 1

Indications of the pilot lamp

Overheat

standby

NOTE: When standby for cooling battery, UC18YRL cools the overheated battery by cooling fan.

Charge status

lamp (RED)

Overheat lamp

(GREEN)

Temperatures at which the

Rechargeable batteries

battery can be recharged

BCL1415, BCL1430,

EBL1430, BCL1815

EBM1830

0°C – 50°C

Charger

UC18YRL

Battery

BCL1415, BCL1815

Approx. 20 min.

BCL1430, EBL1430, EBM1830

Approx. 45 min.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DS 14 DL Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi DS 14 DL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info