Bedienungsanleitung Hitachi DS 14 DL (Seite 16 von 98) (Deutsch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

78236

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

English

(1) Removing the bit

Securely hold the main unit and pull out the bit by

holding the tip with your thumb. (Fig. 21)

(2) Installing the Bit

Install the bit with steps opposite of when removing.

Insert the bit so that the right and left sides are equal,

as shown in Fig. 22.

13. Installing/Removing the side handle

CAUTION:

⅜ Firmly install the side handle. If loose, the side handle

may gyrate or fall out and cause bodily injury.

(1) Install the side handle so that the protrusions on the

main unit and grooves on the side handle interlock.

Tighten the grip after checking that the side handle is

not riding on the slip prevention protrusion. (Fig. 23)

(2) Loosen the grip to remove the side handle.

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade efficiency and

cause possible motor malfunction, sharpen or replace

the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes (Fig. 24)

The motor employs carbon brushes which are

consumable parts. Since and excessively worn carbon

brush can result in motor trouble, replace the carbon

brush with new ones when it becomes worn to or

near the “wear limit”. In addition, always keep carbon

brushes clean and ensure that they slide freely within

the brush holders.

NOTE:

When replacing the carbon brush with a new one, be

sure to use the Hitachi Carbon Brush Code No. 999054.

5. Replacing carbon brushes

Take out the carbon brush by first removing the

brush cap and then hooking the protrusion of the

carbon brush with a flat head screw driver, etc., as

shown in Fig. 26.

When installing the carbon brush, choose the direction

so that the nail of the carbon brush agrees with the

contact portion outside the brush tube. Then push it

in with a finger as illustrated in Fig. 27. Lastly, install

the brush cap.

CAUTION:

Be absolutely sure to insert the nail of the carbon

brush into the contact portion outside the brush tube.

(You can insert whichever one of the two nails

provided.)

Caution must be exercised since any error in this

operation can result in the deformed nail of the carbon

brush and may cause motor trouble at an early stage.

6. Cleaning on the outside

When the driver drill is stained, wipe with a soft dry

cloth or a cloth moistened with soapy water. Do not

use chloric solvents, gasoline or paint thinner, for

they melt plastics.

7. Storage

Store the driver drill in a place in which the

temperature is less than 40°C and out of reach of

children.

8. Service parts list

CAUTION:

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without

prior notice.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country specific regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a Hitachi Authorized Service Center.

NOTE:

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

IMPORTANT:

Correct connection of the plug

The wires of the mains lead are coloured in accordance

with the following code:

Blue: – Neutral

Brown: – Live

As the colours of the wires in the mains lead of this tool

may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black.

The wire coloured brown must be connected to the

terminal marked with the letter L or coloured red.

Neither core must be connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except United Kingdom.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DS 14 DL Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi DS 14 DL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info