Bedienungsanleitung Hitachi ds 14 dsl (Seite 12 von 82) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

389002

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

English

⅜ If the battery is recharged when it is warm due to battery

use or exposure to sunlight, the pilot lamp map light in

green.

The battery will not be recharged. In such a case, let the

battery cool before charging.

⅜ When the pilot lamp flickers in red (at 0.2-second intervals),

check for and take out any foreign objects in the charger’s

battery installation hole. If there are no foreign objects, it is

probable that the battery or charger is malfunctioning.

Take it to your authorized Service Center.

PRIOR TO OPERATION

1. Setting up and checking the work environment

Check if the work environment is suitable by following

the precautions.

HOW TO USE

1. Confirm the clutch dial position (see Fig. 5)

The tightening torque of this unit can be adjusted

according to the clutch dial position, at which the

clutch dial is set.

(1) When using this unit as a screwdriver, line up the one

of the numbers “1, 3, 5 ... 22” on the clutch dial, or

the dots, with the triangle mark on the outer body.

(2)

When using this unit as a drill, align the clutch dial drill

mark “ ” with the triangle mark on the outer body.

CAUTION:

⅜ The clutch dial cannot be set between the numerals

“1, 3, 5 ... 22” or the dots.

⅜ Do not use with the clutch dial numeral between

“22” and the line at the middle of the drill mark.

Doing so may cause damage. (See Fig. 6)

2. Tightening torque adjustment

(1) Tightening torque

Tightening torque should correspond in its intensity

to the screw diameter. When too strong torque is

used, the screw head may be broken or be injured.

Be sure to adjust the clutch dial position according to

the screw diameter.

(2) Tightening torque indication

The tightening torque differs depending on the type

of screw and the material being tightened.

The unit indicates the tightening torque with the

numbers “1, 3, 5 ... 22” on the clutch dial , and the

dots. The tightening toque at position “1” is the

weakest and the torque is strongest at the highest

number. (See Fig. 5)

(3) Adjusting the tightening torque

Rotate the clutch dial and line up the numbers “1, 3,

5, ... 22” on the clutch dial, or the dots, with the

triangle mark on the outer body. Adjust the clutch

dial in the weak or the strong torque direction

according to the torque you need.

CAUTION:

⅜ The motor rotation may be locked to cease while the

unit is used as drill. While operating the driver drill,

take care not to lock the motor.

⅜ Too long hammering may cause the screw broken

due to excessive tightening.

3. Change rotation speed

Operate the shift knob to change the rotational speed.

Move the shift knob in the direction of the arrow (see

Figs. 7 and 8).

When the shift knob is set to “LOW”, the drill rotates at a

low speed.!»en set to “HIGH”, the drill rotates at a high speed.

(2) Regarding the temperatures of the rechargeable

battery

The temperatures for rechargeable batteries are as

shown in Table 2, and batteries that have become

hot should be cooled for a while before being

recharged.

Table 2 Recharging ranges of batteries

(3) Regarding recharging time

Depending on the combination of the charger and

batteries, the charging time will become as shown in

Table 3.

Table 3 Charging time (At 20°C)

NOTE:

The charging time may vary according to temperature

and power source voltage.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger firmly and pull out the battery.

NOTE:

After operation, pull out batteries from the charger

first, and then keep the batteries properly.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the first and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2 – 3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes weaker,

stop using the tool and recharge its battery. If you continue

to use the tool and exhaust the electric current, the battery

may be damaged and its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use.

If such a battery is recharged immediately after use, its

internal chemical substance will deteriorate, and the battery

life will be shortened. Leave the battery and recharge it

after it has cooled for a while.

CAUTION:

⅜

When the battery charger has been continuosly used, the

battery charger will be heated, thus constituting the cause

of the failures. Once the charging has been completed,

give 15 minutes rest until the next charging.

Temperatures at

Rechargeable batteries

which the battery

can be recharged

BSL1430, BSL1415,

0°C – 40°C

BSL1830

Charger

UC18YRSL

Battery

BSL1430, BSL1830

Approx.45 min.

BSL1415

Approx.20 min.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi ds 14 dsl Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi ds 14 dsl

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info