Bedienungsanleitung Hitachi ds 9 dvb (Seite 11 von 70) (Deutsch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

387438

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

English

CAUTION

⅜ The selection examples shown in Table 5 should

be considered as general standard. As different

types of tightening screws and different materials

to be tightened are used in actual works proper

adjustments are naturally necessary.

⅜ When using the driver drill with a machine screw

at HIGH (high speed), a screw may damage or a

bit may loose due to the tightning torque is too

strong. Use the driver drill at LOW (low speed)

when using a machine screw.

NOTE

The use of the battery EB9H, EB930H, EB1222HL,

EB1230HL, EB14H, EB1430H, EB18H and EB1830H

in a cold condition (below 0 degree Centigrade) can

sometimes result in the weakened tightening torque

and reduced amount of work. This, however, is

a temporary phenomenon, and returns to normal

when the battery warms up.

6. Mounting and dismounting of the bit

(1) Mounting the bit

Loosen the sleeve by turning it toward the left (in

the counterclockwise direction as viewed from the

front) to open the clip on the keyless chuck. After

inserting a driver bit, etc., into the keyless drill

chuck, and tighten the sleeve by turning it toward

the right (in the clockwise direction as viewed from

the front). (See Fig. 9)

⅜ If the sleeve becomes loose during operation, tighten

it further.

The tightening force becomes stronger when the

sleeve is tightened additionally.

(2) Dismounting the bit

Loosen the sleeve by turning it toward the left (in

the counterclockwise direction as viewed from the

front), and then take out the bit ect. (See Fig. 9)

NOTE

If the sleeve is tightened in a state where the clip

of the keyless chuck is opened to a maximum limit,

a click noise may occur. This is the noise that occurs

when the loosening of the keyless chuck is prevented

and is not a malfunction.

CAUTION:

⅜ When it is no longer possible to loosen the sleeve,

use a vise or similar instrument to secure the bit.

Set the clutch mode between 1 and 11 and then

turn the sleeve to the loose side (left side) while

operating the clutch. It should be easy now to

loosen the sleeve.

7. Automatic spindle-lock mechanism

This unit has automatic spindle-lock mechanism for

quick bit changes.

8. Confirm that the battery is mounted correctly.

9. Check the rotational direction

The bit rotates clockwise (viewed from the rear

side) by pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn

the bit counterclockwise. (See Fig. 10). (The

and

marks are provided on the body.)

10. Switch operation

⅜ When the trigger switch is depressed, the tool

rotates. When the trigger is released, the tool stops.

⅜ The rotational speed of the drill can be controlled

by varying the amount that the trigger switch is

pulled. Speed is low when the trigger switch is

pulled slightly and increases as the trigger switch

is pulled more.

NOTE

⅜ A buzzing noise is produced when the motor is

about to rotate; This is only a noise, not a machine

failure.

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade efficiency and

cause possible motor malfunction, sharpen or

replace the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Cleaning on the outside

When the driver drill is stained, wipe with a soft

dry cloth or a cloth moistened with soapy water.

Do not use chloric solvents, gasoline or paint thinner,

for they melt plastics.

4. Storage

Store the driver drill in a place in which the tempera

ture is less than 40°C and out of reach of children.

5. Service parts list

A : Item No.

B : Code No.

C : No. Used

D : Remarks

CAUTION:

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed in

each country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

IMPORTANT

Correct connection of the plug

The wires of the mains lead are coloured in accordance

with the following code:

Blue: – Neutral

Brown: – Live

As the colours of the wires in the mains lead of this

tool may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the

terminal marked with the letter N or coloured black.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi ds 9 dvb Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi ds 9 dvb

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info