Bedienungsanleitung Hitachi ds 9dvf3 (Seite 8 von 66) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

386381

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

English

battery and recharge it after it has cooled for a

while.

〈

UC18YG

〉

Before using the driver drill, charge the battery as

follows.

1. Connect the charger power cord to the receptacle

Connecting the power cord will turn on the charger.

2. Insert the battery into the charger

Insert the battery firmly while observing its direction,

until it contacts the bottom of the charger (the pilot

lamp lights up) (See Fig. 4).

CAUTION

If the pilot lamp does not light up, pull out the

power cord from the receptacle and check the

battery mounting condition.

(1) Regarding the temperatures of the rechargeable

battery

The temperatures for rechargeable batteries are as

shown in Table 1.

Table 1 Recharging ranges of batteries

(2) Regarding recharging time

Depending on the combination of the charger and

batteries, the charging time will become as shown

in Table 2.

Table 2 Charging time (At 20°C)

The pilot lamp goes off to indicate that the battery

is fully charged.

The battery charging time becomes longer when a

temperature is low or the voltage of the power

source is too low.

When the pilot lamp does not go off even if more

than 120 minutes have elapsed after starting of the

charging, stop the charging and contact your

HITACHI AUTHORIZED SERVICE CENTER.

CAUTION

If the battery is heated due to direct sunlight,

etc., just after operation, the charger pilot lamp

may not light up. At that time, cool the battery

first, then start charging.

3. Disconnect the charger’s power cord from the

receptacle

4. Hold the charger firmly and pull out the battery

NOTE

After charging, pull out batteries from the charger

first, and then keep the batteries properly.

CAUTION

The UC9SD and UC12SD models are the

exclusively designed charger. These cannot

charge batteries except the specified batteries.

It is possible to insert the batteries other than

the specified into the charger and some of them

may light up the pilot lamps. However, you are

requested to exercise utmost caution not to

charge batteries other than specified ones

because these can not only be charged but also

such actions can result in the malfuntion of

chargers.

2. Connect the charger power cord to the receptacle

Connecting the power cord will turn on the charger

(the pilot lamp lights up).

CAUTION

If the pilot lamp does not light up, pull out the

power cord from the receptacle and check the

battery mounting condition.

About 60 minutes is required to fully charge the

battery at a temperature of about 20°C. The pilot

lamp goes off to indicate that the battery is fully

charged.

The battery charging time becomes longer when a

temperature is low or the voltage of the power

source is too low.

When the pilot lamp does not go off even if more

than 120 minutes have elapsed after starting of the

charging, stop the charging and contact your

HITACHI AUTHORIZED SERVICE CENTER.

CAUTION

If the battery is heated due to direct sunlight,

etc., just after operation, the charger pilot lamp

may not light up. At that time, cool the battery

first, then start charging.

3. Disconnect the charger power cord from the

receptacle

4. Hold the charger firmly and pull out the battery

NOTE

After charging, pull out batteries from the charger

first, and then keep the batteries properly.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an

extended period is not activated, the electric

discharge might be low when using them the first

and second time. This is a temporary phenomenon,

and normal time required for recharging will be

restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the

electric current, the battery may be damaged and

its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

Temperatures at

Rechargeable batteries which the battery

can be recharged

EB912S, EB914S, EB9B,

EB1212S, EB1214S, 0°C – 45°C

EB1220BL

Charger

UC18YG

Battery

EB912S, EB914S,

Approx. 30 min.

EB1212S, EB1214S

EB9B, EB1220BL

Approx. 50 min.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi ds 9dvf3 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi ds 9dvf3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info