Bedienungsanleitung Hitachi DS14DBEL (Seite 13 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566521

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

English

The unit indicates the tightening torque with the

numbers “1, 3, 5 ... 22” on the clutch dial , and the

dots. The tightening toque at position “1” is the

weakest and the torque is strongest at the highest

number. (See Figs. 5)

(3) Adjusting the tightening torque

Rotate the clutch dial and line up the numbers “1, 3,

5, ... 22” on the clutch dial, or the dots, with the

triangle mark on the outer body. Adjust the clutch

dial in the weak or the strong torque direction

according to the torque you need.

CAUTION

⅜ The motor rotation may be locked to cease while the

unit is used as drill. While operating the driver drill,

take care not to lock the motor.

⅜ Too long hammering may cause the screw broken

due to excessive tightening.

3. Change rotation speed

Operate the shift knob to change the rotational speed.

Move the shift knob in the direction of the arrow (see

Figs. 7 and 8).

When the shift knob is set to “LOW”, the drill

rotates at a low speed. When set to “HIGH”, the

drill rotates at a high speed.

CAUTION

⅜ When changing the rotational speed with the shift

knob, confirm that the switch is off.

Changing the speed while the motor is rotating will

damage the gears.

⅜ When setting the shift knob to “HIGH” (high speed)

and the position of the clutch dial is “17” or “22”, it

may happen that the clutch is not engaged and that

the motor is locked. In such a case, please set the

shift knob to “LOW” (low speed).

⅜ If the motor is locked, immediately turn the power

off. If the motor is locked for a while, the motor or

battery may be burnt.

Be sure to turn the shift knob.

4. The scope and suggestions for uses

The usable scope for various types of work based on

the mechanical structure of this unit is shown in

Table 4.

5. How to select tightening torque and rotational speed

Table 4

Work Clutch dial Position Suggestion

Wood

Drilling Steel Use for drilling purpose.

Aluminum

Machine screw

1 – 22 Use the bit or socket matching the screw diameter.

Driving

Wood screw 1 – Use after drilling a pilot hole.

Use

Clutch dial Position

Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Machine screw 1 – 22

For 4 mm or smaller

diameter screws.

Driving

Wood screw 1 –

For 8 mm or smaller

nominal diameter screws.

Drilling

Wood

For 36 mm or smaller

diameters. (DS14DBEL)

For 38 mm or smaller

diameters. (DS18DBEL)

Metal

For drilling with a metal

working drill bit.

For 6 mm or smaller

diameter screws.

For 3.8 mm or smaller

nominal diameter screws.

For 18 mm or smaller

diameters. (DS14DBEL)

For 22 mm or smaller

diameters. (DS18DBEL)

Table 5

01Eng_DS14DBEL_WE.p65 9/18/13, 9:46 AM13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DS14DBEL Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info