Bedienungsanleitung Hitachi DS14DSFL (Seite 12 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566539

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

English

6. Mounting and dismounting of the bit

(1) After inserting a driver bit, etc. into the keyless drill

chuck, ﬁ rmly grasp the ring and tighten the sleeve by

turning it toward the right (in the clockwise direction as

viewed from the front) (See Fig. 9).

○ If the sleeve becomes loose

during operation, tighten it

further. The tightening force becomes stronger when the

sleeve is tightened additionally.

(2) Dismounting the bit

Firmly grasp the ring and loosen the sleeve by turning

it toward the left (in the counter-clockwise direction as

viewed from the front) (See Fig. 9).

CAUTION

When it is no longer

possible to loosen the sleeve, use a

vise or similar instrument to secure the bit. Set the clutch

mode between 1 and 11, and then turn the sleeve to the

loose side (left side) while operating the clutch. It should

be easy now to loosen the sleeve.

7. Conﬁ rm

that the battery is mounted correctly

8. Check the rotational direction

The bit rotates clockwise (viewed from the rear side) by

pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn the bit

counterclockwise (See Fig. 10) (The

and marks

are provided on the body).

9. Switch operation

○ When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

○ The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled.

Speed is low when the

trigger switch is pulled slightly

and increases as the trigger switch is pulled more.

NOTE

A buzzing noise is produced when the motor is about to

rotate; This is only a noise, not a machine failure.

10. Using the hook

The hook is used to hang up the power tool to your

waist

belt while working.

CAUTION

○ When using the hook, hang up the power tool ﬁ rmly not

to drop accidentally.

If the power tool is dropped, it may lead to an accident.

○ When carrying the power tool with hooked to your waist

belt, do not ﬁ t any bit to the tip

of power tool. If the sharp

bit such as drill is ﬁ tted to the power tool when carrying it

with hooked to your waist belt, you will be injured.

○ Install securely the hook. Unless the hook is securely

installed, it may cause an injury while using.

(1) Removing the hook.

Remove

the screws ﬁ xing the hook with screw driver.

(Fig. 11).

(2) Replacing the hook and tightening the screws.

Install securely the hook in the groove of power tool and

tighten the screws to ﬁ x the hook ﬁ rmly. (Fig. 12)

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade eﬃ ciency and

cause possible motor malfunction, sharpen or replace

the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the

screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Cleaning on the outside

When the driver drill is stained, wipe with a soft dry

cloth or a cloth moistened with soapy water. Do not use

chloric solvents, gasoline or paint thinner, for they melt

plastics.

4. Storage

Store the driver drill in a place in which the temperature

less than 40°C and out of reach of children.

NOTE

Make sure that the battery is fully charged when stored

for a long period (3 months or more). The battery with

smaller capacity may not be able to be charged when

used, if stored for a long period.

5. Service parts list

CAUTION

Repair, modiﬁ cation and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the tool to

the Hitachi Authorized Service Center when requesting

repair or other maintenance.

In the operation and maintenance of power tools,

the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modiﬁ ed to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without prior

notice.

Important notice on the batteries for the Hitachi

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modiﬁ ed

(such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a Hitachi Authorized Service Center.

NOTE

Due to HITACHI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

000Book_DS14DSFL_WE.indb 12000Book_DS14DSFL_WE.indb 12 2011/08/19 14:47:452011/08/19 14:47:45

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DS14DSFL Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info