Bedienungsanleitung Hitachi DS18DCL (Seite 12 von 68) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566526

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

English

(2) Dismounting the bit

Firmly grasp the ring and loosen the sleeve by turning

it toward the left (in the counter-clockwise direction as

viewed from the front) (See Fig. 8).

CAUTION

When it is no longer possible to loosen the sleeve, use a

vise or similar instrument to secure the bit. Set the clutch

mode between 1 and 11, and then turn the sleeve to the

loose side (left side) while operating the clutch. It should

be easy now to loosen the sleeve.

7. Conﬁ rm that the battery is mounted correctly

8. Check the rotational direction

The bit rotates clockwise (viewed from the rear side) by

pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn the

bit counterclockwise (See Fig. 9) (The

and marks

are provided on the body).

9. Switch operation

○ When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

○ The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled.

Speed is low when the trigger switch is pulled slightly

and increases as the trigger switch is pulled more.

NOTE

A buzzing noise is produced when the motor is about to

rotate; This is only a noise, not a machine failure.

10. Using the bit holder

CAUTION

○ Stow the bit in the speciﬁ ed location on the tool. If the

tool is used with the bit stowed improperly, the bit may

fall and cause bodily injury.

○ Do not stow bits that are of a diﬀ erent length, gauge or

dimension than the plus driver bit (65 mm long) included

in the STANDARD ACCESSORIES.

The bit may fall and cause bodily injury.

(1) Removing the bit

Securely hold the main unit and pull out the bit by

holding the tip with your thumb (Fig. 10).

(2) Installing the Bit

Install the bit with steps opposite of when removing.

Insert the bit so that the right and left sides are equal, as

shown in Fig. 11

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade eﬃ ciency and

cause possible motor malfunction, sharpen or replace

the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Cleaning on the outside

When the driver drill is stained, wipe with a soft dry

cloth or a cloth moistened with soapy water. Do not use

chloric solvents, gasoline or paint thinner, for they melt

plastics.

4. Storage

Store the driver drill in a place in which the temperature

is less than 40°C and out of reach of children.

NOTE

Make sure that the battery is fully charged when stored

for a long period (3 months or more). The battery with

smaller capacity may not be able to be charged when

used, if stored for a long period.

5. Service parts list

CAUTION

Repair, modiﬁ cation and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the tool to

the Hitachi Authorized Service Center when requesting

repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modiﬁ ed to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without prior

notice.

Important notice on the batteries for the Hitachi

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modiﬁ ed (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a Hitachi Authorized Service Center.

NOTE

Due to HITACHI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

Information concerning airborne noise and vibration

The measured values were determined according to

EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 97 dB (A)

Measured A-weighted sound pressure level: 86 dB (A)

Uncertainty KpA: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN60745.

Vibration emission value

ah, D = 8.8 m/s

Uncertainty K = 1.5 m/s

01Eng_DS14DCL_WETh.indd 1201Eng_DS14DCL_WETh.indd 12 2013/05/24 12:10:002013/05/24 12:10:00

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DS18DCL Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info