Bedienungsanleitung Hitachi dv 10 dva (Seite 26 von 32) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

387422

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

English

GENERAL OPERATIONAL PRECAUTIONS

1. Keep work area clean. Cluttered areas and benches

invite accidents.

2. Avoid dangerous environment. Don’t expose power

tools and charger to rain. Don’t use power tools

and charger in damp or wet locations. And keep

work area well lit.

Never use power tools and charger near flammable

or explosive materials.

Do not use tool and charger in presence of

flammable liquids or gases.

3. Keep children away. All visitors should be kept

safe distance from work area.

4. Store idle tools and charger. When not in use,

tools and charger should be stored in dry, high

or locked-up place-out of reach of children. Store

tools and charger in a place where the tempera-

ture is less than 40°C.

5. Don’t force tool. It will do the job better and safer

at the rate for which it was designed.

6. Use right tool. Don’t force small tool or attach-

ment to do the job of a heavy duty tool.

7. Wear proper apparel. No loose clothing or jewelry

to get caught in moving parts. Rubber gloves and

footwear are recommended when working outdoor.

8. Use safety glasses with most tools. Also face or

dust mask if cutting operation is dusty.

9. Don’t abuse cord. Never carry charger by cord or

yank it to disconnect from receptacle. Keep cord

from heat, oil and sharp edges.

10. Secure work. Use clamps or a vise to hold work.

It’s safer than using your hand and it frees both

hands to operate tool.

11. Don’t overreach. Keep proper footing and balance

at all times.

12. Maintain tools with care. Keep tools sharp at all

times, and clean for best and safest performance.

Follow instructions for lubricating and changing

accessories.

13. When the charger is not in use, or when being

maintained and inspected, disconnect the power

cord of the charger from the AC outlet.

14. Remove chuck wrenches and wrenches. Form habit

of checking to see that wrenches are removed

from tool before turning it on.

15. Avoid accidental starting. Don’t carry tool with

finger on switch.

16. Always use the specifidied charger.

Never use a charger other than that specified to

prevent danger.

17. Use only original HITACHI replacement parts.

18. Do not use power tools for applications other than

those specified in the Handling Instructions.

19. To ensure the designed operational integrity of

power tools and charger, do not remove installed

covers or screws.

20. Consult an authorized Service Agent in the event

of power tool and charger failure.

21. Always use the charger at the voltage specified

on the nameplate.

22. Do not touch movable parts or accessories unless

the battery has been removed.

23. Always charge the battery before use.

24. Never use a battery other than that specified. Do

not connect a usual dry cell, a rechargeable battery

other than that specified or a car battery to the

power tool.

25. Do not use any transformer that has a booster.

26. Do not charge the battery from an engine electric

generator or DC power supply.

27. Always charge indoors. Because the charger and

battery heat slightly during charging, charge the

battery in a place not exposed to direct sunlight;

which has low humidity and is well ventilated.

28. When working in a high place, pay attention to

the activities below to make sure there are no

people below.

PRECAUTIONS FOR CORDLESS IMPACT DRILL

1. Always charge the battery at a temperature of 10 –

40°C. A temperature of less than 10°C will result

in over charging which is dangerous. The battery

cannot be charged at a temperature higher than

40°C. The most suitable temperature for charging

is that of 20 – 25°C.

2. Do not use the charger continuously.

When one charging is completed, leave the charger

for about 15 minutes before the next charging of

battery.

3. Do not charge the battery for more than 2 hour.

The battery will be fully charged in about 1 hour

and charging should be stopped when 1 hour has

elapsed from commencement. Disconnect the

charger power cord from the AC outlet.

4. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

5. Never disassemble the rechargeable battery and

charger.

6. Never short-circuit the rechargeable battery. Short-

circuiting the battery will cause a great electric

current and overheat. It results in burn or damage

to the battery.

7. Do not dispose of the battery in fire.

If the battery is burnt, it may explode.

8. When drilling into wall, floor or ceiling, check for

buried electric power cable, gas pipe, etc.

9. Bring the battery to the shop from which it was

purchased as soon as the post-charging battery

life becomes too short for practical use. Do not

dispose of the exhausted battery.

10. Using an exhausted battery will damage the

charger.

11. Do not insert foreign object into the air ventilation

slots of the charger.

Inserting metal objects or inflammables into the

charger air ventilation slots will result in electrical

shock hazard or damaged charger.

12. When mounting a bit into the keyless chuck, tighten

the sleeve securely. If the sleeve is not tight, the

bit may slip or come off, causing injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi dv 10 dva Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info