Bedienungsanleitung Hitachi DV 14 DL (Seite 45 von 54) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

78870

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

English

and the position of the cap is between“16” and “22”,

it may happen that the clutch does not engaged and

that the motor is locked. In such a case, please set the

shift knob to “LOW” (low speed).

⅜ If the motor is locked, immediately turn the power

off. If the motor is locked for a while, the motor or

battery may be burnt.

⅜ In the work of the save mode (S), avoid the continuous

screw-tightening as temperature of electronic

components of the converter switch increases.

⅜ To extend the lifetime, the lithium-ion battery equips

CAUTION

⅜ The selection examples shown in Table 5 should be

considered as general standard. As different types of

tightening screws and different materials to be

tightened are used in actual works proper adjustments

are naturally necessary.

⅜ When using the impact driver drill with a machine

screw at HIGH (high speed), a screw may damage or

a bit may loose due to the tightning torque is too

strong. Use the impact driver drill at LOW (low speed)

when using a machine screw.

NOTE

The use of the battery BCL1430, EBL1430, EBM1430

and EBM1830 in a cold condition (below 0 degree

Centigrade) can sometimes result in the weakened

tightening torque and reduced amount of work. This,

however, is a temporary phenomenon, and returns

to normal when the battery warms up.

7. Mounting and dismounting of the bit

(1) Mounting the bit

Loosen the sleeve by turning it toward the left (in the

counterclockwise direction as viewed from the front)

to open the clip on the keyless chuck. After inserting

a driver bit, etc., into the keyless drill chuck, and

tighten the sleeve by turning it toward the right (in

the clockwise direction as viewed from the front)

(See Fig. 9).

Table 5

6. How to select tightening torque and rotational speed

Work Suggestions

Brick

Drilling

Wood

Use for drilling purpose.

Steel

Aluminum

Machine screw Use the bit or socket matching the screw diameter.

Driving

Wood screw Use after drilling a pilot hole.

Table 4

Use Cap Position

Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Machine screw 1 – 22

For 4 mm or smaller

diameter screws.

Driving

Wood screw 1 –

For 8 mm or smaller nominal

diameter screws.

Brick

For 14 mm or smaller

diameters. (DV14DL)

For 16 mm or smaller

diameters. (DV18DL)

Drilling

Wood

For 45 mm or smaller

diameters. (DV14DL)

For 50 mm or smaller

diameters. (DV18DL)

Metal

For drilling with a metal

working drill bit.

For 6 mm or smaller

diameter screws.

For 4.8 mm or smaller

nominal diameter screws.

For 10 mm or smaller

diameters. (DV14DL)

For 12 mm or smaller

diameters. (DV18DL)

For 20 mm or smaller

diameters. (DV14DL)

For 22 mm or smaller

diameters. (DV18DL)

with the protection function to stop the output.

Therefore, if the tool is overloaded, the motor may

stop. However, this is not the trouble but the result of

protection function. In this case, release the switch of

tool and eliminate the causes of overloading.

5. The scope and suggestions for uses

The usable scope for various types of work based on

the mechanical structure of this unit is shown in

Table 4.

⅜ If the sleeve becomes loose during operation, tighten

it further.

The tightening force becomes stronger when the

sleeve is tightened additionally.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DV 14 DL Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi DV 14 DL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info