Bedienungsanleitung Hitachi dv 14 dsl (Seite 11 von 76) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

389273

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

English

CAUTION

⅜ When the battery charger has been continuosly used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next

charging.

⅜ If the battery is recharged when it is warm due to

battery use or exposure to sunlight, the pilot lamp

map light in green.

The battery will not be recharged. In such a case, let

the battery cool before charging.

⅜

When the pilot lamp flickers in red (at 0.2-second intervals),

check for and take out any foreign objects in the charger’s

battery installation hole. If there are no foreign objects, it

is probable that the battery or charger is malfunctioning.

Take it to your authorized Service Center.

PRIOR TO OPERATION

1. Setting up and checking the work environment

Check if the work environment is suitable by following

the precautions.

HOW TO USE

1. Confirm the cap position (see Fig. 5)

The three modes of screwdriver, drill and impact drill

can be switched by the position of the cap in this unit.

(1) When using this unit as a screwdriver, line up the one

of the numbers “1, 3, 5 ... 22” on the cap, or the black

dots, with the triangle mark on the outer body.

(2) When using this unit as a drill, align the cap drill mark

“

” with the triangle mark on the outer body.

(3) When using this unit as an impact drill, align the cap

hammer mark “ ” with the triangle mark on the

outer body.

CAUTION

⅜ The cap cannot be set between the numerals “1, 3, 5

... 22” or the black dots.

⅜ Do not use with the cap numeral between “22” and

the black line at the middle of the drill mark. Doing so

may cause damage (See Fig. 6).

2. Tightening torque adjustment

(1) Tightening torque

Tightening torque should correspond in its intensity

to the screw diameter. When too strong torque is

used, the screw head may be broken or be injured.

Be sure to adjust the cap position according to the

screw diameter.

(2) Tightening torque indication

The tightening torque differs depending on the type

of screw and the material being tightened.

The unit indicates the tightening torque with the

numbers “1, 3, 5 ... 22” on the cap, and the black

dots. The tightening toque at position “1” is the

weakest and the torque is strongest at the highest

number (See Fig. 5).

(3) Adjusting the tightening torque

Rotate the cap and line up the numbers “1, 3, 5 ... 22”

on the cap, or the black dots, with the triangle mark on

the outer body. Adjust the cap in the weak or the strong

torque direction according to the torque you need.

CAUTION

⅜ The motor rotation may be locked to cease while the

unit is used as drill. While operating the impact driver

drill, take care not to lock the motor.

⅜ Too long hammering may cause the screw broken

due to excessive tightening.

3. Rotation to Impact changeover (See Fig. 5)

The “Rotation (Rotation only)” and “Impact (Impact

+ Rotation)” can be switched by aligning the drill

mark “

” or the hammer mark “ ” with the triangle

mark on the outer body.

⅜ To make holes in the metal, wood or plastic, switch

to “Rotation (Rotation only)”.

⅜ To make holes in bricks or concrete blocks, switch to

“Impact (Impact + Rotation)”.

CAUTION

If an operation which is normally performed at the

“Rotation” setting is performed at “Impact “ setting,

the effect of making holes does not only increase but

it may also damage the bit or other parts.

4. Change rotation speed

Operate the shift knob to change the rotational speed.

Move the shift knob in the direction of the arrow (see

Figs. 7 and 8).

When the shift knob is set to “LOW”, the drill

rotates at a low speed.!»en set to “HIGH”, the drill

rotates at a high speed.

CAUTION

⅜ When changing the rotational speed with the shift

knob, confirm that the switch is off.

Changing the speed while the motor is rotating will

damage the gears.

⅜ When setting the shift knob to “HIGH” (high speed)

and the position of the cap is bitween “17” and “22”,

it may happen that the clutch does not engaged and

that the motor is locked. In such a case, please set the

shift knob to “LOW” (low speed).

⅜ If the motor is locked, immediately turn the power

off. If the motor is locked for a while, the motor or

battery may be burnt.

5. The scope and suggestions for uses

The usable scope for various types of work based on

the mechanical structure of this unit is shown in

Table 4.

Work Suggestions

Brick

Drilling

Wood

Use for drilling purpose.

Steel

Aluminum

Machine screw Use the bit or socket matching the screw diameter.

Driving

Wood screw Use after drilling a pilot hole.

Table 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi dv 14 dsl Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi dv 14 dsl

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info