Bedienungsanleitung Hitachi dv 24 dv (Seite 8 von 46) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

387433

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

English

APPLICATIONS

⅜ By combined actions of ROTATION and IMPACT:

Boring holes in hard materials (concrete, brick, tiles,

etc.)

⅜ By ROTATIONAL action:

Boring holes in steel, wood and plastic.

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latches

to remove the battery (see Figs. 1 and 2).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery aligning both guide rail of battery

and body. Make sure the battery is fixed firmly.

CHARGING

Before using the impact drill, charge the battery as follows.

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charger’s

pilot lamp will blink in red. (At 1-second intervals).

2. Insert the battery into the charger.

Insert the battery into the charger as shown in Fig.

3. Make sure the battery is fully seated in the

charger.

3. Charging

When inserting a battery in the charger, charging

will commence and the pilot lamp will light up

continuously in red.

When the battery becomes fully recharged, the pilot

lamp will blink in red. (At 1-second intervals.) (See

Table 1)

(1) Pilot lamp indication

The indications of the pilot lamp are shown in

Table 1, according to the condition of the charger

or the rechargeable battery.

Table 1

Indications of the pilot lamp

Lights for 0.5 seconds. Does not light for 0.5

seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for 0.5

seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for 0.1

seconds. (off for 0.1 seconds)

Lights continuously

Before

charging

While

charging

Charging

complete

Charging

impossible

Charging

impossible

Blinks

(RED)

Lights

(RED)

Blinks

(RED)

Flickers

(RED)

Lights

(GREEN)

Malfunction in the battery

or the charger

The battery temperature

is high, making recharging

impossible.

(2) Regarding the temperatures of the rechargeable

battery.

The temperatures for rechargeable batteries are as

shown in the table 2, and batteries that have become

hot should be cooled for a while before being

recharged.

Table 2

(3) Regarding recharging time

Depending on the type of battery, the charging time

will become as shown in Table 3.

Temperatures at

Battery type which the battery

can be recharged

EB2420 –5°C – 60°C

EB2430HA 0°C – 45°C

Table 3 Charging time (At 20°C)

NOTE

The charging time may vary according to

temperature and power source voltage.

4. Disconnect the charger’s power cord from the

receptacle.

5. Hold the charger firmly and pull out the battery.

NOTE

After operation, pull out batteries from the charger

first, and then keep the batteries properly.

Battery type Recharging time

EB2420 Approx. 50 min.

EB2430HA Approx. 70 min.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi dv 24 dv Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi dv 24 dv

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info