Bedienungsanleitung Hitachi DV14DCL2 (Seite 12 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566551

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

English

(2) Tightening torque indication

The tightening torque diﬀ ers depending on the type of

screw and the material being tightened.

The unit indicates the tightening torque with the numbers

“1, 3, 5 ... 22” on the clutch dial, and a dots. The tightening

toque at position “1” is the weakest

and the torque is

strongest at the highest number (See Fig. 4).

(3) Adjusting the tightening torque

Rotate the clutch dial and line up the numbers “1, 3, 5 ...

22” on the clutch dial, or the dots, with the triangle mark

on the outer body. Adjust the clutch dial

in the weak or the

strong torque direction according to the torque you need.

CAUTION

○ The motor rotation may be locked to cease while the unit

is used as drill. While operating the impact driver drill,

take care not to lock the motor.

○ Too long hammering may cause the screw

broken due to

excessive tightening.

3. Rotation to Impact changeover (See Fig. 4)

The “Rotation (Rotation only)” and “Impact (Impact +

Rotation)” can be switched by aligning the drill mark “

”

or the hammer mark “

” with the triangle mark on the

outer body.

○ To make holes in the metal, wood or plastic, switch to

“Rotation (Rotation only)”.

○ To make holes in bricks or concrete blocks, switch to

“Impact (Impact + Rotation)”.

CAUTION

○ If an operation which is normally performed at the

“Rotation” setting is

performed at “Impact” setting, the

eﬀ ect of making holes does not only increase but it may

also damage the bit or other parts.

○ If it is hard to turn the clutch dial to hammer mark

“

” position, turn the chuck slightly in either direction

and then turn the clutch dial to hammer mark “

” position

again.

4. Change rotation speed

Operate the shift knob to change the rotational speed.

Move the shift knob in the direction of the arrow (See

Figs. 6 and 7).

When the shift knob is set to “LOW”, the drill rotates at a

low speed. When set to “HIGH”, the

drill rotates at a high

speed.

CAUTION

○ When changing the rotational speed with the shift knob,

conﬁ rm that the switch is oﬀ .

Changing the speed while the motor is rotating will

damage the gears.

○ When setting the shift knob to “HIGH” (high speed) and

the position of the

clutch dial is between “15” and “22”, it

may happen that the clutch does not engaged and that

the motor is locked. In such a case, please set the shift

knob to “LOW” (low speed).

○ If the motor is locked, immediately turn the power oﬀ . If

the motor

is locked for a while, the motor or battery may

be burnt.

○ To extend the lifetime, the lithium-ion battery equips with

the protection function to stop the output.Therefore, if the

tool is overloaded, the motor may stop. However, this is

not the trouble but the result of protection function. In

this

case, release the switch of tool and eliminate the causes

of overloading.

5. The scope and suggestions for uses

The usable scope for various types of work based on the

mechanical structure of this unit is shown in Table 4.

Table 4

Work Suggestions

Drilling

Brick

Use for drilling purpose.

Wood

Steel

Aluminum

Driving

Machine screw Use the bit or socket matching the screw diameter.

Wood screw Use after drilling a pilot hole.

6. How to select tightening torque and rotational speed

Table 5

Use

Clutch Dial

Position

Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Driving

Machine screw 1 – 22

For 4 mm or smaller diameter

screws.

For 6 mm or smaller diameter

screws.

Wood screw

1 –

For 8 mm or smaller nominal

diameter screws.

For 4.8 mm or smaller nominal

diameter screws.

Drilling

Brick

For 13 mm or smaller diameters.

For 8 mm or smaller diameters.

(DV14DCL2)

For 10 mm or smaller diameters.

(DV18DCL2)

Wood

For 32 mm or smaller diameters.

(DV14DCL2)

For 18 mm or smaller diameters.

(DV14DCL2)

For 38 mm or smaller diameters.

(DV18DCL2)

For 22 mm or smaller diameters.

(DV18DCL2)

Metal

For drilling with a metal working drill

bit.

000Book_DV14DCL2_WE,Tha.indb 12000Book_DV14DCL2_WE,Tha.indb 12 2012/04/06 13:50:282012/04/06 13:50:28

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DV14DCL2 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info