Bedienungsanleitung Hitachi DV14DSFL (Seite 10 von 68) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566555

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

English

Table 1

Indications of the pilot lamp

Pilot lamp

(red)

Before

charging

Blinks

Lights for 0.5 seconds. Does not light for 0.5

seconds. (oﬀ for 0.5 seconds)

While

charging

Lights

Lights continuously

Charging

complete

Blinks

Lights for 0.5 seconds. Does not light for 0.5

seconds. (oﬀ for 0.5 seconds)

Overheat

standby

Blinks

Lights for 1 second. Does not light for 0.5

seconds. (oﬀ for 0.5 seconds)

Battery overheated.

Unable to charge.

(Charging will commence

when battery cools)

Charging

impossible

Flickers

Lights for 0.1 second. Does not light for 0.1

seconds. (oﬀ for 0.1 seconds)

Malfunction in the

battery or the charger

you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use.

If such a battery is recharged immediately after use, its

internal chemical substance will

deteriorate, and the

battery life will be shortened. Leave the battery and

recharge it after it has cooled for a while.

CAUTION

○ If the battery is charged while it is heated because it has

been left for a long time in a location subject to direct

sunlight or because the battery

has just been used, the

pilot lamp of the charger lights for 1 second, does not

light for 0.5 seconds (oﬀ for 0.5 seconds). In such a case,

ﬁ rst let the battery cool, then start charging.

○ When the pilot lamp ﬂ ickers (at 0.2-second intervals),

check for and take out

any foreign objects in the charger’s

battery connector. If there are no foreign objects, it is

probable that the battery or charger is malfunctioning.

Take it to your authorized Service Center.

○ Since the built-in micro computer takes about 3

seconds to conﬁ rm that the battery being charged with

UC18YGSL

is taken out, wait for a minimum of 3 seconds

before reinserting it to continue charging. If the battery

is reinserted within 3 seconds, the battery may not be

properly charged.

PRIOR TO OPERATION

1. Setting up and checking the work environment

Check if the work environment is suitable by following the

precautions.

HOW TO USE

1. Conﬁ rm the clutch dial position (See Fig. 5)

The three modes of screwdriver, drill and impact drill can

be switched by the position of the cap in this unit.

(1) When using this unit as a screwdriver, line up the one of

the numbers “1, 3, 5 ... 22”

on the clutch dial, or the dots,

with the triangle mark on the outer body.

(2) When using this unit as a drill, align the clutch dial drill

mark “

” with the triangle mark on the outer body.

(3) When using this unit as an impact drill, align the cap

hammer mark “

” with the triangle mark on the outer

body.

(2) Regarding the temperature of the rechargeable battery.

The temperatures for rechargeable batteries are as

shown in Table 2, and batteries that have become hot

should be cooled for a while before being recharged.

Table 2 Recharging ranges of batteries

Rechargeable batteries

Temperatures at

which the battery

can be recharged

BSL1415, BSL1815 0°C – 50°C

(3) Regarding time

Depending on the combination of the charger and

batteries, the charging time will become as shown in

Table 3.

Table 3 Charging time (At 20°C)

Charger

Battery

UC18YGSL

BSL1415, BSL1815 Approx. 40 min.

NOTE

The charging time may vary according to temperature

and power source voltage.

4. Disconnect the charger’s power cord from the

receptacle

5. Hold the charger ﬁ rmly and pull out the battery

NOTE

After charging, pull out batteries from the charger ﬁ rst,

and then keep the batteries

properly.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries and

batteries that have not been used for an extended period

is not activated, the electric discharge might be low when

using them the ﬁ rst and second time. This is a temporary

phenomenon, and

normal time required for recharging

will be restored by recharging the batteries 2-3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery. If

000Book_DV14DSFL_WE.indb 10000Book_DV14DSFL_WE.indb 10 2011/03/23 12:00:472011/03/23 12:00:47

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DV14DSFL Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info