Bedienungsanleitung Hitachi DV14DVC (Seite 10 von 78) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

566562

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

English

CAUTION

⅜ The selection examples shown in Table 5 should be

considered as general standard. As different types of

tightening screws and different materials to be

tightened are used in actual works proper adjustments

are naturally necessary.

⅜ When using the impact driver drill with a machine

screw at HIGH (high speed), a screw may damage or

a bit may loose due to the tightning torque is too

strong. Use the impact driver drill at LOW (low speed)

when using a machine screw.

NOTE

The use of the battery

EB1426H, EB1430H, EB1826HL,

EB1830HL

and EBM1830 in a cold condition (below 0

degree Centigrade) can sometimes result in the

Work Suggestions

Brick

Drilling

Wood

Use for drilling purpose.

Steel

Aluminum

Machine screw Use the bit or socket matching the screw diameter.

Driving

Wood screw Use after drilling a pilot hole.

Table 4

6. How to select tightening torque and rotational speed

⅜ Too long hammering may cause the screw broken

due to excessive tightening.

3. Rotation to Impact changeover (See Fig. 5)

The “Rotation (Rotation only)” and “Impact (Impact

+ Rotation)” can be switched by aligning the drill

mark “

” or the hammer mark “ ” with the triangle

mark on the outer body.

⅜ To make holes in the metal, wood or plastic, switch

to “Rotation (Rotation only)”.

⅜ To make holes in bricks or concrete blocks, switch to

“Impact (Impact + Rotation)”.

CAUTION

If an operation which is normally performed at the

“Rotation” setting is performed at “Impact “

setting,the effect of making holes does not only

increase but it may also damage the bit or other

parts.

4. Change rotation speed

Operate the shift knob to change the rotational speed.

Move the shift knob in the direction of the arrow (see

Figs. 7

and

When the shift knob is set to “LOW”, the drill rotates

at a low speed. When set to “HIGH”, the drill rotates

at a high speed.

CAUTION

⅜ When changing the rotational speed with the shift

knob, confirm that the switch is off.

Changing the speed while the motor is rotating will

damage the gears.

⅜ When setting the shift knob to “HIGH” (high speed)

and the position of the cap is bitween “16” and “22”,

it may happen that the clutch does not engaged and

that the motor is locked. In such a case, please set the

shift knob to “LOW” (low speed).

⅜ If the motor is locked, immediately turn the power

off. If the motor is locked for a while, the motor or

battery may be burnt.

⅜ To extend the lifetime, the lithium-ion battery equips

with the protection function to stop the output.

Therefore, if the tool is overloaded, the motor may

stop. However, this is not the trouble but the result of

protection function. In this case, release the switch of

tool and eliminate the causes of overloading.

5. The scope and suggestions for uses

The usable scope for various types of work based on

the mechanical structure of this unit is shown in

Table 4.

Table 5

Use Cap Position

Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Machine screw 1 – 22

For 6 mm or smaller

diameter screws.

Driving

Wood screw 1 –

For 6 mm or smaller nominal

diameter screws.

Brick

For 13 mm or smaller

diameters.

Drilling

Wood

For 32 mm or smaller

diameters. (DV14DVC)

For 38 mm or smaller

diameters. (DV18DCL/

DV18DVC)

Metal

For drilling with a metal

working drill bit.

For 6 mm or smaller

diameter screws.

For 3.8 mm or smaller

nominal diameter screws.

For 8 mm or smaller

diameters. (DV14DVC)

For 10 mm or smaller

diameters. (DV18DCL/

DV18DVC)

For 18 mm or smaller

diameters. (DV14DVC)

For 22 mm or smaller

diameters. (DV18DCL/

DV18DVC)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi DV14DVC Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info