Bedienungsanleitung Hitachi EC 10SB (Seite 9 von 18) (Englisch)

597519

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

— 9 —

4. Confirm the power receptacle

If the power receptacle only loosely accepts the plug,

the receptacle must be repaired. Contact the nearest

electric store for repair service.

If such a faulty receptacle is used, may cause

overheating, resulting in a serious hazard.

5. Dipstick insertion and oil level check

(If your compressor is EC10SB(SL) this step is not

necassary.)

Use a screwdriver or similar tool to remove the plastic

cap on the lower part of the cylinder (Fig. 3).

(EC12)

Fig. 3

Insert the accessory dipstick all the way to the bottom.

Remove the dipstick and make sure the oil level is

within the range of the dipstick notches (Fig. 4).

(EC12)

Fig. 4

WARNING:Drain tank to release air pressure

before removing the dipstick.

WARNING:Make sure air vent in dipstick is free

from debris. If air vent is blocked

pressure can build in crankcase

causing damage to compressor and

possible personal injury.

When the oil volume is insufficient, refer to the section

“Oil change-oil topping off” on page 10 for a descrip-

tion of how to supply the oil.

6. Right running position

Position the compressor on a flat surface , in a well

ventilated area away from atmospheric agents and

not in explosive areas.

TRANSPORT

Push the knob of the pressure switch to "OFF" and

disconnect it from the power source before move the

compressor. Transport the compressor in the correct

manner.

OPERATION

1. Start up

Insert the plug into the receptacle and start the

compressor by pulling the knob of the pressure switch

to “ON” (Refer to Fig. 2).

WARNING: Do not stop or start the compressor

by use of the plug. Always use “ON/

OFF” knob located on the pressure

switch.

The operation of the compressor is automatic and is

controlled by the pressure switch which stops it when

the pressure in the air-tank reaches the maximum

level and restart it when the air pressure drops during

use to the restart level.

The motor of the compressor is fitted with a thermal

protection inside-the wrap, which stops the

compressor when the temperature is too high. Should

this be tripped, the compressor will restart

automatically after 15-20 minutes.

2. Adjustment of working pressure

Unlock the knob of the pressure reducer pulling it up,

adjust the pressure to the required level by turning the

knob clockwise to increase and counterclockwise to

decrease.

A pressure gauge (B) is provided to know when the

required pressure is reached, lock the knob by

pushing it down firmly (Refer to Fig. 5).

When adjusting the pressure, check and make sure

that a pressure gauge for the tank has the pressure

level that is higher than that of the pressure to be

adjusted.

It is also imperative that you make adjustment by

slowly starting up the pressure from the level that is

lower than the pressure to be adjusted.

WARNING: Check the manufacturer’s maximum

pressure rating for nailers, staplers

and accessories. Compressor outlet

pressure must be regulated so as to

never exceed the maximum pressure

rating of the nailers, staplers and

accessories.

Dipstick

MAX.

MIN.

Air vent

Plastic cap

Cylinder

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi EC 10SB Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info