Bedienungsanleitung Hitachi fds 9 dva (Seite 22 von 29) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

387444

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

English

GENERAL OPERATIONAL PRECAUTIONS

1. Keep work area clean. Cluttered areas and benches

invite accidents.

2. Avoid dangerous environment. Don’t expose

power tools and charger to rain. Don’t use power

tools and charger in damp or wet locations. And

keep work area well lit.

Never use power tools and charger near flammable

or explosive materials.

Do not use tool and charger in presence of

flammable liquids or gases.

3. Keep children away. All visitors should be kept

safe distance from work area.

4. Store idle tools and charger. When not in use,

tools and charger should be stored in dry, high

or locked-up place-out of reach of children. Store

tools and charger in a place in which the tem-

perature is less than 40°C.

5. Don’t force tool. It will do the job better and safer

at the rate for which it was designed.

6. Use right tool. Don’t force small tool or attach-

ment to do the job of a heavy duty tool.

7. Wear proper apparel. No loose clothing or jewelry

to get caught in moving parts. Rubber gloves and

footwear are recommended when working

outdoor.

8. Use safety glasses with most tools. Also face or

dust mask if cutting operation is dusty.

9. Don’t abuse cord. Never carry charger by cord

or yank it to disconnect from receptacle. Keep

cord from heat, oil and sharp edges.

10. Secure work. Use clamps or a vise to hold work.

It’s safer than using your hand and it frees both

hands to operate tool.

11. Don’t overreach. Keep proper footing and balance

at all times.

12. Maintain tools with care. Keep tools sharp at all

times, and clean for best and safest performance.

Follow instructions for lubricating and changing

accessories.

13. When the charger is not in use or when being

maintained and inspected, disconnect its power

cord of the charger from the AC outlet.

14. Remove chuck wrenches and wrenches. Form

habit of checking to see that wrenches are removed

from tool before turning it on.

15. Avoid accidental starting. Don’t carry tool with

finger on switch.

16. Always use only the specified charger.

Never use a charger other than that spacified to

prevent danger.

17. Use only genuine HITACHI replacement parts.

18. Do not use power tools for applications other

than those specified in the Handling Instructions.

19. To ensure the designed operational integrity of

power tools and charger, do not remove installed

covers or screws.

20. Consult an authorized Service Agent in the event

of power tool and charger failure.

21. Always use the charger at the voltage specified

on the name plate.

22. Do not touch movable parts or accessories unless

the power source has been disconnected.

23. Always charge the battery before use.

24 . Never use a battery other than that specified. Do

not connect a usual dry cell, a rechargeable battery

other than that specified or a car battery to the

power tool.

25. Do not use any transformer containing a booster.

26. Do not charge the battery from an engine electric

generator or DC power supply.

27. Always charge indoors. As the charger and battery

heat-up slightly during charging, charge the battery

in a place not exposed to direct sunlight, whch

has low humidity and is well ventilated.

28. When working in a high place, pay attention to

activities below. Before commencing, ensure that

there are no people below.

PRECAUTIONS FOR CORDLESS DRIVER

DRILL

1. Always charge the battery at a temperature of

10 –40°C. A temperature of less than 10°C will

result in over charging which is dangerous. The

battery cannot be charged at a temperature higher

than 40°C. The most suitable temperature for

charging is that of 20 – 25°C.

2. When one charging is completed, leave the charger

for about 15 minutes before the next charging of

battery.

Do not charge more than two batteries

consecutively.

3. Do not charge the battery for more than 2 hours.

The battery will be fully charged in about 1 hour

and charging should be stopped when 1 hour has

elapsed from commencement. Disconnect the

charger power cord from the receptacle.

4. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

5. Never disassemble the rechargeable battery and

charger.

6. Never short-circuit the rechargeable battery. Short-

circuiting the battery will cause a great electric

current and overheat. It results in burn or damage

to the battery.

7. Do not dispose of the battery in fire.

If the battery is burnt, it may explode.

8. When drilling in wall, floor or ceiling, check for

buried electric power cord, etc.

9. Bring the battery to the shop from which it was

purchased as soon as the post-charging battery

life becomes too short for practical use. Do not

dispose of the exhausted battery.

10. Using an exhausted battery will damage the

charger.

11. Do not insert object into the air ventilation slots

of the charger.

Inserting metal objects or inflammables into the

charger air ventilation slots will result in electrical

shock hazard or damaged charger.

12. When mounting a bit into the keyless chuck,

tighten the sleeve adequately. If the sleeve is not

tight, the bit may slip or come off, causing injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi fds 9 dva Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info