Bedienungsanleitung Hitachi fds 9 dva (Seite 25 von 29) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

387444

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

English

Table 2

Use Cap Position

Rotating speed selection (Position of the shift knob)

LOW (Low speed) HIGH (High speed)

Machine screw 1 – 22

For 4 mm or smaller

diameter screws.

Driving

Wood screw 1 –

For 5.5 mm or smaller

nominal diameter screws.

Drilling

Wood

For 18 mm or smaller

diameters. (FDS9DVA)

For 21 mm or smaller

diameters. (FDS12DVA)

Metal

For drilling with a metal

working drill bit.

For 6 mm or smaller

diameter screws.

For 3.8 mm or smaller

nominal diameter screws.

For 12 mm or smaller

diameters

CAUTION

⅜ The selection examples shown in Table 2 should

be utilized as a general standard. As different types

of tightening screws and different materials to be

tightened are used in actual works, proper

adjustments are naturally necessary.

6. Mounting and dismounting of the bit.

(1) After inserting a driver bit, etc. into the keyless drill

chuck, firmly grasp the ring and tighten the sleeve

by turning it toward the right (in the clockwise

direction as viewed from the front). (See Fig. 8)

⅜ If the sleeve becomes loose during operation, tighten

it further. The tightening force becomes stronger

when the sleeve is tightened additionally.

(2) Dismounting the bit

Firmly grasp the ring and loosen the sleeve by

turning it toward the left (in the counter-clockwise

direction as viewed from the front). (See Fig. 8)

CAUTION:

⅜ When it is no longer possible to loosen the sleeve,

use a vise or similar instrument to secure the bit.

Set the clutch mode between 1 and 10 and then

turn the sleeve to the loose side (left side) while

operating the clutch. It should be easy now to

loosen the sleeve.

NOTE

⅜ There is a plus driver bit on side of the main unit.

The bit can be removed by pulling it forward. After

using the bit, make sure to firmly attach it to the

main body again.

7. Confirm that the battery is mounted correctly.

8. Check the rotation direction

The bit rotates clockwise (viewed from the rear

side) by pushing the R-side of the selector button.

The L-side of the selector button is pushed to turn

the bit counterclockwise. (see Fig. 9). (The

and

marks are provided on the body.)

CAUTION:

⅜ Make sure to firmly switch the selector button. If

it is not switched firmly, the drill may not rotate

even if the switch is turned on.

9. Switch operation

When the trigger switch is pulled, the tool rotates.

When the trigger is released, the tool stops.

⅜ The rotational speed of the drill can be controlled

by varying the amount that the trigger switch is

pulled. Speed is low when the trigger switch is

pulled slightly and increases as the trigger switch

is pulled more.

NOTE

⅜ A peep sound may be produced when the motor

is about to rotate; This is only a noise, not a machine

failure.

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of as dull tool will degrade efficiency and

cause possible motor malfunction, sharpen or

replace the tool as soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Cleaning on the outside

When the driver drill is stained, wipe with a soft

dry cloth or a cloth moistened with soapy water.

Do not use chloric solvents, gasoline or paint thinner,

as they melt plastics.

4. Storage

Store the driver drill in a place in which the tempera

ture is less than 40°C and out of reach of children.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

5. How to select tightening power and rotation speed

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi fds 9 dva Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info