Bedienungsanleitung Hitachi fs 10 sa (Seite 5 von 26) (Englisch)

389692

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

English

SPECIFICATIONS

Voltage (by areas)*

Power input

No-load speed

Sanding pad size

Sanding paper size

Weight (without cord)

(110V, 115V, 120V, 127V, 220V, 230V, 240V)

180W*

10000/min

92 mm x 184 mm

93 mm x 228 mm

1.4 kg

*Be sure to check the nameplate on product as it is subject to change by areas.

NOTE:

Models FS10SB and FS10SA are the same except that the former is equipped with the dust cover and adaptor as

standard accessories.

STANDARD ACCESSORIES

1. Sanding paper .......................................................... 3

(Grain: #60, #100, #150................................ 1 each)

2. Dust cover ................................................1 (FS10SB)

3. Adaptor ..................................................... 1 (FS10SB)

Standard accessories are subject to change without no-

tice.

OPTIONAL ACCESSORIES (sold separately)

⅜ Sanding paper

Grain: #60, #100, #150, (3 types)

⅜ Dust cover (FS10SA)

⅜ Adaptor (FS10SA)

Optional accessories are subject to change without

notice.

APPLICATIONS

⅜ Finish polishing of woodwork surfaces

⅜ Sanding surfaces of woodwork or sheet metal prior

to painting, etc.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized con-

forms to the power requirements specified on the

product nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, inviting a serious

accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Installing the sanding paper

(1) Removing the dust cover: (FS10SB)

While slightly opening the dust cover front, raise

the dust cover front as shown in Fig. 1. Disengage

the dust cover rear from the body as shown in Fig.

2. The dust cover is removed.

(2) Mounting the sanding paper:

Insert the sanding paper while unfastening the spring

as shown in Fig. 3. Align the sanding paper in

parallel with the pad and pull it tight.

Should the sanding paper be loosely mounted, the

finishing will become uneven or the sanding paper

may be damaged.

(to facilitate mounting the sanding paper)

After engaging the one side of sanding paper, fold

the other side 10 mm from the edge as shown in

Fig. 4.

Fold the sanding paper again 10 mm from the

folded edge.

(3) Installing the dust cover: (FS10SB)

Position the dust cover as shown in Fig. 5. Engage

the dust cover rear as shown in Fig. 6. And depress

the dust cover front downward.

(4) Installing the cleaner: (FS10SB)

Connect the suction hose to the dust cover hole.

(If the suction hose cannot be connected, attach the

supplied adaptor and fix with tape).

PRACTICAL OPERATING PROCEDURES

CAUTION

Never apply water or grinding fluid when sanding. This

could result in electrical shock.

1. Switching the sander ON and OFF

By pulling the trigger and pushing the stopper, the

switch will remain ON even when the trigger is

released, promoting continuous, efficient operation.

By pulling the trigger again, the stopper is released

and the switch is turned OFF.

CAUTION

Never turn the power switch ON when the sander

is contacting the surface to be sanded. This is

necessary to preclude damage to the material. The

same applies when switching the power OFF.

2. How to hold the orbital sander

While gripping the knob with one hand and the

handle with the other, lightly press the sander against

the surface to be sanded so that the sanding paper

uniformly contacts the surface. DO NOT apply

excessive pressure to the sander while sanding.

Excessive pressure may cause overload of the motor,

reduced service life of the sanding paper, and lower

sanding or polishing efficiency. Also, while sanding

or polishing, never cover the ventilation port on the

upper motor housing. This could cause overheating

and subsequent damage to the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi fs 10 sa Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi fs 10 sa

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info