Bedienungsanleitung Hitachi g 12 se (Seite 16 von 22) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

391182

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

English

GENERAL OPERATIONAL PRECAUTIONS

1. Keep work area clean. Cluttered areas and benches

invite injuries.

2. Consider work area environment. Don’t expose

power tools t o rain. Don’t use power tools in damp

or wet locations. Keep work area well lit.

Don’t use tools in presece of flammable liquids or

gases.

Power tools produce sparks during operation.

They also spark when switching ON/OFF. Never

use power tools in dangerous sites containing

lacquer, paint, benzine, thinner, gasoline, gases,

adhesive agents, and other materials which are

combustible or explosive.

3. Guard against electric shock. Prevent body contact

with grounded surfaces. For example; pipes,

radiators, ranges, refrigerator enclosures.

4. Kep children away. Do not let visitors contact tool

or extension cord. All visitors should be kept away

from work area.

5. Store idle tools. When not in use, tools should be

stored in dry and high or locked-up place—out of

reach of children.

6. Don’t force tools. It will do the job better and safer

at the rate or which it was intended.

7. Use right tool. Don’t force small tool or attachment

to do the job of a heavy—duty tool. Don’t use tool

for purpose not intended—for example—don’t use

circular saw for cutting tree limbs or logs.

8. Dress properly. Do not wear loose clothing or

jewelry. They can be caught in moving parts. Rubber

gloves and non-skid footwear are recommended

when working outdoors. Wear protective hair

covering to contain long hair.

9. Use safety glasses. Also use face or dust mask if

cutting operation is dusty.

10. Don’t abuse cord. Never carry tool by cord or yank

it do disconnect from receptacle. Keep cord from

heat, oil and sharp edges.

11. Secure work. Use clamps or a vise to hold work.

It’s safer than using your hand and it frees both

hands to operate tool.

12. Don’t overreach. Keep proper footing and balance

at all times.

13. Maintain tools with care. Keep tools sharp and clean

for better and safer performance. Follow instructions

for lubricating and changing accessories. Inspect

tool cords periodically and if damaged, have repaired

by authorized service center. Inspect extension cords

periodically and replace if damaged. Keep handles

dry, clean, and free from oil and grease.

14. Disconnect tools. When not in use, before servicing,

and when changing accessories, such as blades,

bits, cutters.

15. Remove adjusting keys and wrenches. Form habit

of checking to see that keys and adjusting wrenches

are removed from tool before turning it on.

16. Avoid unintentional starting. Don’t carry plugged-

in tool with finger on switch. Be sure switch is off

when plugging in.

17. Outdoor use extension cords. When tool is used

outdoors, use only extension cords intended for use

for outdoors and so marked.

18. Stay alert. Watch what you are doing. Use common

sense. Do not operate tool when you are tired.

19. Check damaged parts. Before further use of the tool,

a guard or other part that is damaged should be

carefully checked to determine that it will operate

properly and perform its intended function. Check

for alignment of moving parts, binding of moving

parts, breakage of parts, mounting, and any other

conditions that may affect its operation. A guard

or other part that is damaged should be properly

repaired or replaced by an authorized service center

unless otherwise indicated elsewhere in this

instruction manual. Have defective switches replaced

by authorized service center. Do not use tool if

switch does not turn it on and off.

20. Do not use power tools for applications other than

those specified in the Handling Instructions.

21. To ensure the designed operational integrity of power

tools, do not remove installed covers or screws.

22. Do not touch movable parts or accessories unless

the power source has been disconnected.

23. Use your tool at lower input than specified on the

nameplate; otherwise, the finish may be spoiled

and working efficiency reduced due to motor

overload.

24. Do not wipe plastic parts with solvent. Solvents

such as gasoline, thinner, benzine, carbon

tetrachloride, alcohol, ammonia and oil containing

chloric annex may damage and crack plastic parts.

Do not wipe them with such solvent. Wipe plastic

parts with a soft cloth lightly dampened with soapy

water.

25. Consult an authorized Service Agent in the event

of power tool failure.

26. Use only genuine HITACHI replacement parts.

27.This tool should only be disassembled for

replacement of carbon brushes.

PRECAUTIONS ON USING DISC GRINDER

1. This product shall be applied to industrial use.

2. Never operate these power tools without Wheel

Guards.

3. Use only grinding wheels with a “Safe Speed” at

least as high as the “No-Load Speed” indicated on

the power tool nameplate.

4. Always hold the body handle and side handle of

the power tools firmly. Otherwise the counterforce

produced may result in inaccurate and even

dangerous operation.

5. Never depress the push button while the spindle

is turning.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi g 12 se Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi g 12 se

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info