Bedienungsanleitung Hitachi G 13 SB 3 (Seite 7 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

78338

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

English

d) Use special care when working corners, sharp edges

etc. Avoid bouncing and snagging the accessory.

Corners, sharp edges or bouncing have a tendency

to snag the rotating accessory and cause loss of

control or kickback.

e) Do not attach a saw chain woodcarving blade or

toothed saw blade.

Such blades create frequent kickback and loss of

control.

SAFETY WARNINGS SPECIFIC FOR

GRINDING AND ABRASIVE CUTTING-OFF

OPERATIONS

a) Use only wheel types that are recommended for

your power tool and the specific guard designed

for the selected wheel.

Wheels for which the power tool was not designed

cannot be adequately guarded and are unsafe.

b) The guard must be securely attached to the power

tool and positioned for maximum safety, so the

least amount of wheel is exposed towards the

operator.

The guard helps to protect operator from broken

wheel fragments and accidental contact with wheel.

c) Wheels must be used only for recommended

applications. For example: do not grind with the

side of cut-off wheel.

Abrasive cut-off wheels are intended for peripheral

grinding, side forces applied to these wheels may

cause them to shatter.

d) Always use undamaged wheel flanges that are of

correct size and shape for your selected wheel.

Proper wheel flanges support the wheel thus

reducing the possibility of wheel breakage. Flanges

for cut-off wheels may be different from grinding

wheel flanges.

e) Do not use worn down wheels from larger power

tools.

Wheel intended for larger power tool is not suitable

for the higher speed of a smaller tool and may

burst.

ADDITIONAL SAFETY WARNINGS SPECIFIC

FOR ABRASIVE CUTTING-OFF OPERATIONS

a) Do not “jam” the cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive

depth of cut.

Overstressing the wheel increases the loading and

susceptibility to twisting or blinding of the wheel

in the cut and the possibility of kickback or wheel

breakage.

b) Do not position your body in line with and behind

the rotating wheel.

When the wheel, at the point of operation, is moving

away from your body, the possible kickback may

propel the spinning wheel and the power tool directly

at you.

c) When wheel is binding or when interrupting a cut

for any reason, switch off the power tool and hold

the power tool motionless until the wheel comes

to a complete stop. Never attempt to remove the

cut-off wheel from the cut while the wheel is in

motion otherwise kickback may occur.

Investigate and take corrective action to eliminate

the cause of wheel binding.

d) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully reenter the cut.

The wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

e) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own

weight. Supports must be placed under the

workpiece near the line of cut and near the edge

of the workpiece on both sides of the wheel.

f) Use extra caution when making a “pocket cut” into

existing walls or other blind areas.

The protruding wheel may cut gas or water pipes,

electrical wiring or objects that can cause kickback.

GENERAL SAFETY INSTRUCTIONS FOR

GRINDERS

– Check that speed marked on the wheel is equal to

or greater than the rated speed of the grinder;

– Ensure that the wheel dimensions are compatible

with the grinder;

– Abrasive wheels shall be stored and handled with

care in accordance with manufacturer’s instructions;

– Inspect the grinding wheel before use, do not use

chipped, cracked or otherwise defective products;

– Ensure that mounted wheels and points are fitted

in accordance with the manufacturer’s instructions;

– Ensure that blotters are used when they are provided

with the bonded abrasive product and when they

are required;

– Ensure that the abrasive product is correctly mounted

and tightened before use and run the tool at no-

load for 30 s in a safe position, stop immediately

if there is considerable vibration or if other defects

are detected. If this condition occurs, check the

machine to determine the cause;

– If a guard is equipped with the tool never use the

tool without such a guard;

– Do not use separate reducing bushings or adapters

to adapt large hole abrasive wheels;

– For tools intended to be fitted with threaded hole

wheel, ensure that the thread in the wheel is long

enough to accept the spindle length;

– Check that the work piece is properly supported;

– Do not use cutting off wheel for side grinding;

– Ensure that sparks resulting from use do not create

a hazard e.g. do not hit persons, or ignite flammable

substances;

– Ensure that ventilation openings are kept clear when

working in dusty conditions, if it should become

necessary to clear dust, first disconnect the tool

from the mains supply (use non metallic objects)

and avoid damaging internal parts;

– Always use eye and ear protection. Other personal

protective equipment such as dust mask, gloves,

helmet and apron should be worn;

– Pay attention to the wheel that continues to rotate

after the tool is switched off.

01Eng_ G12SA3_WE 08/12/10, 14:316

Hitachi G 13 SB 3 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info