Bedienungsanleitung Hitachi g 13 sc2 (Seite 7 von 45) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

390615

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

English

PRACTICAL GRINDER APPLICATION

1. Pressure

To prolong the life of the machine and ensure a

first class finish, it is important that the machine

should not be overloaded by applying too much

pressure. In most applications, the weight of the

machine alone is sufficient for effective grinding.

Too much pressure will result in reduced rotational

speed, inferior surface finish, and overloading which

could reduce the life of the machine.

2. Grinding angle

Do not apply the entire surface of the depressed

center wheel to the material to be ground. As

shown in Fig. 2, the machine should be held at an

angle of 15° – 30° so that the external edge of the

depressed center wheel contacts the material at an

optimum angle.

3. To prevent a new depressed center wheel from

digging into the workpiece, initial grinding should

be performed by drawing the grinder across the

workpiece toward the operator (Fig. 2 direction B).

Once the leading edge of the depressed center

wheel is properly abraded, grinding may be

conducted in either direction.

4. Precautions immediately after finishing operation

The wheel continues to rotate after the tool is

switched off.

After switching off the machine, do not put it down

until the depressed center wheel has come to a

complete stop. Apart from avoiding serious

accidents, this precaution will reduce the amount

of dust and swarf sucked into the machine.

CAUTIONS

⅜ Check that the work piece is properly supported.

⅜ Ensure that ventilation openings are kept clear when

working in dusty conditions.

If it should become necessary to clear dust, first

disconnect the tool from the mains supply (use non-

metallic objects) and avoid damaging internal parts.

⅜ Ensure that sparks resulting from use do not create

a hazard e.g. do not hit persons, or ignite flammable

substances.

⅜ Always use protective safety glasses and hearing

protectors, use other personal protective equipment

such as gloves, apron and helmet when necessary.

⅜ Always use eye and ear protection.

Other personal protective equipment such as dust

mask, gloves, helmet and apron should be worn

when necessary.

If in doubt, wear the protective equipment.

⅜ When the machine is not use, the power source

should be disconnected.

ASSEMBLING AND DISASSEMBLING THE

DEPRESSED CENTER WHEEL (Fig. 1)

CAUTION: Be sure to switch OFF and disconnect the

attachment plug from the receptacle to avoid

a serious accident.

1. Assembling (Fig. 1)

(1) Turn the equipment upsidedown so that the spindle

will be facing up.

(2) Mount the wheel washer onto the spindle.

(3) Fit the protuberance of the depressed center wheel

onto the wheel washer.

(4) Screw from above the wheel nut onto the spindle.

(5) As shown in Fig. 1, push in the push button to

prevent rotation of the spindle. Then, secure the

depressed center wheel by tightening the wheel nut

with the wrench.

2. Disassembling

Follow the above procedures in reverse.

CAUTIONS

⅜ Comfirm that the depressed center wheel is mounted

firmly.

⅜ Confirm that the push button is disengaged by

pushing push button two or three times before

switching the power tool on.

MAINTENANCE AND INSPECTION

1. Inspecting the depressed center wheel

Ensure that the depressed center wheel is free of

cracks and surface defects.

2. Inspecting the mounting screws:

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Inspecting the carbon brushes (Fig. 3)

The motor employs carbon brushes which are

consumable parts.

When they become worn to or near the “wear

limit”, it could result in motor trouble. When an

auto-stop carbon brush is equipped, the motor will

stop automatically.

At that time, replace both carbon brushes with new

ones which have the same carbon brush numbers

shown in the figure. In addition, always keep carbon

brushes clean and ensure that they slide freely

within the brush holders.

4. Replacing a carbon brush

Disassemble the brush cap with a slotted-head

screwdriver. The carbon brush can then be easily

removed.

5. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool. Exercise due care to ensure the winding

does not become damaged and/or wet with oil or

water.

6. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by an Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed in

each country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi g 13 sc2 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi g 13 sc2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info