Bedienungsanleitung Hitachi G10SD2 (Seite 6 von 45) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

511958

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

English

PRECAUTIONS ON USING DISC GRINDER

1. Never operate these power tools without Wheel

Guards.

2. Check that speed marked on the wheel is equal to

or greater than the rated speed of the grinder.

Use only depressed center wheels rated at 80m/s

(72m/s only for 100 mm disc grinders) or more.

3. Ensure that the wheel dimensions are compatible

with the grinder and that the wheel fits the spindle.

4. Abrasive wheels shall be stored and handled with

care in accordance with manufacturer’s instructions.

5. Inspect the depressed center wheel before use, do

not use chipped, cracked or otherwise defective

products.

6. Always hold the body handle and side handle of

the power tool firmly. Otherwise the counterforce

produced may result in inaccurate and even

dangerous operation.

7. Do not use cutting-off wheels for side grinding.

8. Do not use of separate reducing bushings or adapters

to adapt large hole abrasive wheels.

9. The wheel continues to rotate after the tool is

switched off.

STANDARD ACCESSORIES

(1) Depressed center wheel .......................................... 1

(2) Wrench ........................................................................ 1

(3) Side handle ................................................................ 1

Standard accessories are subject to change without

notice.

APPLICATIONS

⅜ Removal of casting fin and finishing of various

types of steel, bronze and aluminum materials and

castings.

⅜ Grinding of welded sections or sections cut by

means of a cutting torch.

⅜ Grinding of synthetic resins, slate, brick, marble, etc.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Fitting and adjusting the wheel guard

The wheel guard is a protective device to prevent

injury should the depressed center wheel shatter

during operation. Ensure that the guard is properly

fitted and fastened before commencing grinding

operation. By slightly loosening the setting screw,

the wheel guard can be turned and set at any

desired angle for maximum operational

effectiveness. Ensure that the setting screw is

thoroughly tightened after adjusting the wheel guard.

5. Ensure that the depressed center wheel to be utilized

is the correct type and free of cracks or surface

defects. Also ensure that the depressed center wheel

is properly mounted and the wheel nut is securely

tightened, Refer to the section on “ASSEMBLING

AND DISASSEMBLING THE DEPRESSED CENTER

WHEEL”

6. Conducting a trial run

Ensure that the abrasive products is correctly

mounted and tightened before use and run the tool

at no-load for 30 seconds in a safe position, stop

immediately if there is considerable vibration or if

other defects are detected.

If this condition occurs, check the machine to

determine the cause.

7. Confirm the push button.

Confirm that the push button is disengaged by

pushing push button two or three times before

switching the power tool on (See Fig. 2).

8. Fixing the side handle.

Screw the side handle into the gear cover.

PRACTICAL GRINDER APPLICATION

1. Pressure

To prolong the life of the machine and ensure a

first class finish, it is important that the machine

should not be overloaded by applying too much

pressure. In most applications, the weight of the

machine alone is sufficient for effective grinding.

SPECIFICATIONS

*Be sure to check the nameplate on product as it is subject to change by areas.

Model G10SD2 G12S2 G13SD

Voltage (by areas)* (110V, 115V, 220V, 230V, 240V)

Power Input* 800 W

No-load speed* 11000 min

10000 min

Wheel

outer dia. × hole dia. 100 × 16 mm 115 × 22 mm 125 × 22 mm

peripheral speed 72 m/s 80 m/s

Weight (only main body) 1.6 kg

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi G10SD2 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info