Bedienungsanleitung Hitachi G15YC2 (Seite 10 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

567033

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

English

SPECIFICATIONS

*Be sure to check the nameplate on product as it is subject to change by areas.

Electronic Control

The grinder has an electronic speed control which

provides:

⅜ full speed at all times in the range up to rated load.

⅜ soft-start.

⅜ Kickback Protection

The kickback protection feature cuts off the power

to the motor and stops the power tool in the event

of a sudden drop in the rotational speed of the

wheel during operation (for example, if the wheel

locks during cutting operation, etc.).

⅜ 0 Voltage Re-start Protection

The 0 voltage restart protection feature prevents the

power tool from restarting after the power has been

temporarily cut off during operation.

⅜ Overload Protection

The overload protection feature shuts off the power

to the motor in the event of overloading of the

motor or a conspicuous reduction in rotational speed

during operation.

NOTE:

The grinder is equipped with a rotational speed control

circuit. The rotational speed may fluctuate slightly due

to the conditions of use and working voltage.

STANDARD ACCESSORIES

(1) Depressed center wheel .......................................... 1

(2) Wrench ........................................................................ 1

(3) Side handle ................................................................ 1

(4) Hex. bar wrench ....................................................... 1

Standard accessories are subject to change without

notice.

APPLICATIONS

⅜ Removal of casting fin and finishing of various

types of steel, bronze and aluminum materials and

castings.

⅜ Grinding of welded sections or sections cut by

means of a cutting torch.

⅜ Grinding of synthetic resins, slate, brick, marble, etc.

⅜ Cutting of synthetic concrete, stone, brick, marble,

and similar materials.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

NOTE:

When connected to the power supply, the built-in

electronic control circuit shifts to standby status and

the grinder becomes slightly warm, but this is not

a malfunction.

CAUTION

Do not operate from a direct current power source,

engine generator, booster or any other type of

transformer. Doing so may not only cause damage

to the grinder, but may lead to accidents.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

When the kickback protection, 0 voltage re-start

protection or overload protection feature has been

activated, return the power switch to the OFF position

and wait for 1 second or more before re-starting

the power tool.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Fitting and adjusting the wheel guard

The wheel guard is a protective device to prevent

injury should the depressed center wheel be

shattered during operation. Ensure that the wheel

guard is properly fitted and fastened before

commencing grinding operation.

Model G13YC2 G15YC2

Voltage (by areas)* (110V, 230V, 240V)

Power Input* 1500 W

No-load speed* 10500 min

-1

9000 min

-1

Wheel

outer dia. × hole dia. 125 × 22.23 mm 150 × 22.23 mm

peripheral speed 80 m/s

Weight (only main body) 2.0 kg

– Ensure that ventilation openings are kept clear when

working in dusty conditions, if it should become

necessary to clear dust, first disconnect the tool

from the mains supply (use non metallic objects)

and avoid damaging internal parts;

– Always use eye and ear protection. Other personal

protective equipment such as dust mask, gloves,

helmet and apron should be worn;

– Pay attention to the wheel that continues to rotate

after the tool is switched off.

CAUTION

When using a abrasive cutting wheel, be sure to

remove the standard accessory wheel guard and

attach the wheel guard with side guard (sold

separately). (Fig. 1)

01Eng_G13YC2_WE 1/17/12, 8:289

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi G15YC2 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info