Bedienungsanleitung Hitachi G18DMR (Seite 8 von 89) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

511967

Zoom out

Zoom in

Vorherige Seite

1/89

Nächste Seite

English

– If a guard is equipped with the tool never use the

tool without such a guard;

– Do not use separate reducing bushings or adapters

to adapt large hole abrasive wheels;

– For tools intended to be fitted with threaded hole

wheel, ensure that the thread in the wheel is long

enough to accept the spindle length;

– Check that the work piece is properly supported;

– Do not use cutting off wheel for side grinding;

– Ensure that sparks resulting from use do not create

a hazard e.g. do not hit persons, or ignite flammable

substances;

– Ensure that ventilation openings are kept clear when

working in dusty conditions, if it should become

necessary to clear dust, first disconnect the tool

from the mains supply (use non metallic objects)

and avoid damaging internal parts;

– Always use eye and ear protection. Other personal

protective equipment such as dust mask, gloves,

helmet and apron should be worn;

– Pay attention to the wheel that continues to rotate

after the tool is switched off.

– Always charge the battery at a temperature of 0

– 40°C.

A temperature of less than 0°C will result in over

charging which is dangerous. The battery cannot

be charged at a temperature greater than 40°C.

The most suitable temperature for charging is that

of 20 – 25°C.

– Do not use the charger continuously.

When one charging is completed, leave the charger

for about 15 minutes before the next charging of

battery.

– Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

– Never disassemble the rechargeable battery and

charger.

– Never short-circuit the rechargeable battery.

Short-circuiting the battery will cause a great electric

current and overheat. It results in burn or damage

to the battery.

– Do not dispose of the battery in fire.

If the battery burnt, it may explode.

– Do not insert object into the air ventilation slots of

the charger.

Inserting metal objects or inflammables into the

charger air ventilation slots will result in electrical

shock hazard or damaged charger.

– Bring the battery to the shop from which it was

purchased as soon as the post-charging battery life

becomes too short for practical use. Do not dispose

of the exhausted battery.

– Using an exhausted battery will damage the charger.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips

with the protection function to stop the output.

In the cases of 1 and 2 described below, when using

this product, even if you are pulling the switch, the

motor may stop. This is not the trouble but the result

of protection function.

1. When the battery power remaining runs out (The

battery voltage drops to about 12V (G18DL) /

about 8V (G14DL)), the motor stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In

this case, release the switch of tool and eliminate

causes of overloading. After that, you can use it

again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on

the battery.

⅜ During work make sure that swarf and dust do

not fall on the battery.

⅜ Make sure that any swarf and dust falling on the

power tool during work do not collect on the

battery.

⅜ Do not store an unused battery in a location

exposed to swarf and dust.

⅜ Before storing a battery, remove any swarf and

dust that may adhere to it and do not store it

together with metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such

as a nail, strike with a hammer, step on, throw

or subject the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or

car cigarette lighter sockets.

6. Do not use the battery for a purpose other than

those specified.

7. If the battery charging fails to complete even

when a specified recharging time has elapsed,

immediately stop further recharging.

8. Do not put or subject the battery to high

temperatures or high pressure such as into a

microwave oven, dryer, or high pressure container.

9. Keep away from fire immediately when leakage

or foul odor are detected.

10. Do not use in a location where strong static

electricity generates.

11. If there is battery leakage, foul odor, heat

generated, discolored or deformed, or in any way

appears abnormal during use, recharging or

storage, immediately remove it from the equipment

or battery charger, and stop use.

CAUTION

1. If liquid leaking from the battery gets into your

eyes, do not rub your eyes and wash them well

with fresh clean water such as tap water and

contact a doctor immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well

with clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you find rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the first time, do not use and return

it to your supplier or vendor.

01Eng_G14DMR_WE 11/8/07, 17:207

Hitachi G18DMR Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info