Bedienungsanleitung Hitachi G18DSLS (Seite 13 von 88) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

567038

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

English

ASSEMBLING AND DISASSEMBLING THE

DEPRESSED CENTER WHEEL (Fig. 6)

CAUTION: Be sure to turn off the switch and pull out the

battery.

1. Assembling (Fig. 6)

(1) Turn the disc grinder upsidedown so that the spindle

is facing upward.

(2) Align the across flats of the wheel washer with the

notched part of the spindle, then attach them.

(3) Fit the protuberance of the depressed center wheel

onto the wheel washer.

(4) Screw the wheel nut onto the spindle.

(5) While pushing the push button with one hand, lock

the spindle by turning the depressed center wheel

slowly with the other hand.

Tighten the wheel nut by using the supplied wrench

as shown in Fig. 6.

2. Disassembling

Follow the above procedures in reverse.

CAUTIONS

⅜ Confirm that the depressed center wheel is mounted

firmly.

⅜ Confirm that the push button is disengaged by

pushing push button two or three times before

switching the power tool on.

MAINTENANCE AND INSPECTION

1. Inspecting the depressed center wheel

Ensure that the depressed center wheel is free of

cracks and surface defects.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes (Fig. 8)

The motor employs carbon brushes which are

consumable parts. Since and excessively worn

carbon brush can result in motor trouble, replace

the carbon brush with new ones when it becomes

worn to or near the “wear limit”. In addition, always

keep carbon brushes clean and ensure that they

slide freely within the brush holders.

NOTE

When replacing the carbon brush with a new one,

be sure to use the Hitachi Carbon Brush Code No.

999054.

5. Replacing carbon brushes

Take out the carbon brush by first removing the

brush cap and then hooking the protrusion of the

carbon brush with a slotted head screw driver, etc.,

as shown in Fig. 10.

When installing the carbon brush, choose the

direction so that the nail of the carbon brush agrees

with the contact portion outside the brush tube.

Then push it in with a finger as illustrated in Fig.

11. Lastly, install the brush cap.

CAUTION

Be absolutely sure to insert the nail of the carbon

brush into the contact portion outside the brush

tube. (You can insert whichever one of the two

nails provided.)

Caution must be exercised since any error in this

operation can result in the deformed nail of the

carbon brush and may cause motor trouble at an

early stage.

6 Cleaning of the outside

When the cordless disc grinder is stained, wipe with

a soft dry cloth or a cloth moistened with soapy

water. Do not use chloric solvents, gasoline or paint

thinner, as they melt plastics.

7. Storage

Store the cordless disc grinder in a place in which

the temperature is less than 40°C, and out of reach

of children.

8. Service parts list

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed in

each country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without

prior notice.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country specific regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a Hitachi Authorized Service Center.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

01Eng_G18DSL_WE 08/3/27, 10:5312

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi G18DSLS Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info