Bedienungsanleitung Hitachi G18SW (Seite 11 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

568844

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

English

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country specific regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a Hitachi Authorized Service Center.

NOTE:

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

IMPORTANT:

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: -Neutral

Brown: -Live

As the colours of the wires in the main lead of this tool

may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black. The wire

coloured brown must be connected to the terminal mark-

ed with the letter L or coloured red. Neither core must be

connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not

be applicable to other markets except The United

Kingdom.

Information concerning airborne noise and vibration

The measured values were determined according to

EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 100 dB (A).

Measured A-weighted sound pressure level: 89 dB (A).

Uncertainty KpA: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN60745.

Surface grinding:

Vibration emission value

h, AG

= 5.3 m/s

Uncertainty K = 1.5 m/s

The declared vibration total value has been measured in

accordance with a standard test method and may be used

for comparing one tool with another.

It may also be used in a preliminary assessment of

exposure.

WARNING

⅜ The vibration emission during actual use of the

power tool can differ from the declared total value

depending on the ways in which the tool is used.

⅜ Identify safety measures to protect the operator that

are based on an estimation of exposure in the

actual conditions of use (taking account of all parts

of the operating cycle such as the times when the

tool is switched off and when it is running idle in

addition to the trigger time).

ⅷ Information about power supply system of nominal

voltage 230 V~

Under unfavorable mains conditions, this power tool may

cause

transient voltage drops

interfering voltage

fluctuations

This power tool is intended for the connection to a power

supply system with a maximum permissible system

impedance Z

MAX

of 0.28 Ohm at the interface point (power

service box) of the user's supply.

The user has to ensure that this power tool is connected

only to a power supply system which fulfills the

requirement above.

If necessary, the user can ask the public power supply

company for the system impedance at the interface

point.

01Eng_G18SW_WE 6/28/12, 9:40 AM10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi G18SW Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info