Bedienungsanleitung Hitachi G23SS (Seite 8 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

568843

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

English

SPECIFICATIONS

*1 Be sure to check the nameplate on product as it is subject to change by areas.

*2 Weight: Only main body

STANDARD ACCESSORIES

(1) Wrench ........................................................................ 1

(2) Side handle ................................................................ 1

Depressed center wheels are not provided as standard

accessories.

Standard accessories are subject to change without

notice.

APPLICATIONS

⅜

Removal of casting fin and finishing of various types

of steel, bronze and aluminum materials and castings.

⅜ Grinding of welded sections or sections cut by

means of a cutting torch.

⅜ Grinding of synthetic resins, slate, brick, marble, etc.

⅜ Cutting of synthetic concrete, stone, brick, marble

and similar materials.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Fitting and adjusting the wheel guard (Fig. 1)

The wheel guard is a protective device to prevent

injury should the depressed center wheel shatter

during operation. Ensure that the guard is properly

fitted and fastened before commencing grinding

operation.

By slightly loosening the setting screw, the wheel

guard can be turned and set at any desired angle

for maximum operational effectiveness. Ensure that

the setting screw is thoroughly tightened after

adjusting the wheel guard.

5. Ensure that the depressed center wheel to be utilized

is the correct type and free of cracks or surface

defects. Also ensure that the depressed center wheel

is properly mounted and the wheel nut is securely

tightened. Refer to the section on “ASSEMBLING

AND DISASSEMBLING THE DEPRESSED CENTER

WHEEL”.

6. Conducting a trial run

Ensure that the abrasive products is correctly

mounted and tightened before use and run the tool

at no-load for 30 seconds in a safe position, stop

immediately if there is considerable vibration or if

other defects are detected.

If this condition occurs, check the machine to

determine the cause.

7. Confirm the spindle lock mechanism

Confirm that the spindle lock is disengaged by

pushing push button two or three times before

switching the power tool on (See Fig. 1).

8. Fixing the side handle

Screw the side handle into the gear cover.

PRACTICAL GRINDER APPLICATION

1. Pressure

To prolong the life of the machine and ensure a

first class finish, it is important that the machine

should not be overloaded by applying too much

pressure. In most applications, the weight of the

machine alone is sufficient for effective grinding.

Too much pressure will result in reduced rotational

speed, inferior surface finish, and overloading which

could reduce the life of the machine.

Model G18SS G23SS

Voltage (by areas)*

(110 V, 220 V, 230 V, 240 V)

Input*

2000 W

No-load speed 8500 min

-1

6600 min

-1

Outer dia. 180 mm 230 mm

Wheel Hole dia. 22.23 mm

Peripheral speed 80 m/s

Weight*

4.3 kg

– Ensure that ventilation openings are kept clear when

working in dusty conditions, if it should become

necessary to clear dust, first disconnect the tool

from the mains supply (use non metallic objects)

and avoid damaging internal parts;

– Always use eye and ear protection. Other personal

protective equipment such as dust mask, gloves,

helmet and apron should be worn;

– Pay attention to the wheel that continues to rotate

after the tool is switched off.

01Eng_G18SS_WE 9/2/11, 2:06 PM7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi G23SS Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info