Bedienungsanleitung Hitachi G23UDY (Seite 10 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

568850

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

English

SPECIFICATIONS

*1 Be sure to check the nameplate on product as it is subject to change by areas.

*2 Weight: According to EPTA-Procedure 01/2003

Electronic Control

The grinder has an electronic control which provides:

⅜ soft-start.

⅜ 0 Voltage Re-start Protection

The 0 voltage restart protection feature prevents the

power tool from restarting after the power has been

temporarily cut off during operation.

STANDARD ACCESSORIES

(1) Wrench ........................................................................ 1

(2) Side handle ................................................................ 1

(3) Hexagonal bar wrench ............................................. 1

Depressed center wheels are not provided as standard

accessories.

Standard accessories are subject to change without

notice.

APPLICATIONS

⅜

Removal of casting fin and finishing of various types

of steel, bronze and aluminum materials and castings.

⅜ Grinding of welded sections or sections cut by

means of a cutting torch.

⅜ Grinding of synthetic resins, slate, brick, marble, etc.

⅜ Cutting of synthetic concrete, stone, brick, marble

and similar materials.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

CAUTION

Do not operate from a direct current power source,

engine generator, booster or any other type of

transformer. Doing so may not only cause damage

to the grinder, but may lead to accidents.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Fitting and adjusting the wheel guard

The wheel guard is a protective device to prevent

injury should the depressed center wheel shatter

during operation. Ensure that the guard is properly

fitted and fastened before commencing grinding

operation.

[Installing and adjusting the wheel guard] (Fig. 2)

⅜ Open the lever and insert the locating pin of wheel

guard, bringing it into line with the across flats of

packing ground.

⅜ Then, turn the wheel guard to a desired position

(for use).

⅜ Close the lever and fix it. If and when required, carry

out adjustments by tightening or loosening the screw.

⅜ If the lever does not move smoothly, apply some

lubricating oil to the sliding section between the set

piece and the lever.

⅜ Fasten the wheel guard at the position where the

across flats of the wheel guard positioning pin and

packing ground are aligned (the position where the

wheel guard is inserted), but do not use it.

5. Ensure that the depressed center wheel to be utilized

is the correct type and free of cracks or surface

defects. Also ensure that the depressed center wheel

is properly mounted and the wheel nut is securely

tightened, refer to the section on “ASSEMBLING AND

DISASSEMBLING THE DEPRESSED CENTER WHEEL”.

6. Conducting a trial run

Ensure that the abrasive products is correctly

mounted and tightened before use and run the tool

at no-load for 30 seconds in a safe position, stop

immediately if there is considerable vibration or if

other defects are detected.

If this condition occurs, check the machine to

determine the cause.

7. Confirm the spindle lock mechanism

Confirm that the spindle lock is disengaged by

pushing push button two or three times before

switching the power tool on (See Fig. 1).

8. Fixing the side handle

Screw the side handle into the gear cover.

Model G18UDY G23UCY G23UDY

Voltage (by areas)*

(230 V, 240V)

Input*

2600 W 2400 W 2600 W

Rated Speed 8500 min

-1

6600 min

-1

Outer dia. 180 mm 230 mm

Wheel

Hole dia. 22.23 mm

Thickness 6 mm

Peripheral speed 80 m/s

Weight*

6.4 kg 6.6 kg

01Eng_G18UDY_WE 12/20/12, 12:189

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi G23UDY Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info