Bedienungsanleitung Hitachi H60MC (Seite 8 von 104) (Alle Sprachen)

511985

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

English

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the

accessories listed in the below.

○ Case.............................................................................1

○ Bull Point (SDS-max shank) .........................................1

○ Side Handle { I type: bar type handle ......................1

II type: D type handle ........................1

Either type I or type II Side handle is attached.

Standard accessories are subject to change without notice.

APPLICATIONS

Demolishing concrete, chipping oﬀ concrete, grooving, bar

cutting, and driving piles.

Application examples:

Installation of piping and wiring, sanitary facility installation,

machinery installation, water supply and drainage work,

interior jobs, harbor facilities and other civil engineering

works.

SPECIFICATIONS

Voltage (by areas)* (110 V, 120 V, 127 V,

220 V, 230 V, 240 V)

Power Input* 1250 W

Full-load Impact Rate 1600 min-1

Weight

(According to EPTA

Procedure 01/2014) 11.3 kg

* Be sure to check the nameplate on product as it is

subject to change by areas.

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

MOUNTING AND OPERATION

Action Figure Page

Mounting a tool 22

Deciding working position of tool 32

Fixing the side handle

(Bar type handle) 42

Move the side handle

(D type handle) 53

Switch operation 63

How to use the demolition hammer* 73

Replacing carbon brushes 8 3

Installing the side handle 10, 11 4

Selecting accessories ―5

* By utilizing the empty weight of the machine and by

ﬁ rmly holding the demolition hammer with both hands,

one can eﬀ ectively control the subsequent recoil motion.

Proceed at a moderate work-rate, the use of too much

force will impair eﬃ ciency.

CAUTION

After long time of use, the cylinder case becomes hot.

Therefore, be careful not to burn your hands.

GREASE REPLACEMENT

This machine is of full air-tight construction to protect against

dust and to prevent lubricant leakage. This machine can be

used without grease supplement for an extended period of

time. However, perform the grease replacement to maintain

the service life. Replace the grease as described below.

1. Grease Replacement Period

You should look at the grease when you change the

carbon brush. (See the section MAINTENANCE AND

INSPECTION.) Ask for grease replacement at the

nearest authorized HiKOKI Service Center.

In the case that you are forced to change the grease by

yourself, please follow the following points.

2. How to replace grease

CAUTION

Before replacing the grease, turn the power oﬀ and pull

out the plug from the receptacle.

(1) Remove the crank cover and wipe oﬀ the old grease

inside.

(2) Supply 76 g (the standard volume to cover the

connecting rod) of HiKOKI Electric Hammer Grease A to

the crank case.

(3) After replacing the grease, install the crank cover

securely. At this time, do not damage or lose the oil seal.

NOTE

The HiKOKI Electric Hammer Grease A is of the low

viscosity type. When the grease is consumed, purchase

from an authorized HiKOKI Service Center.

MAINTENANCE AND INSPECTION

CAUTION

Be sure to switch OFF and disconnect the attachment

plug from the receptacle to avoid a serious accident.

1. Inspecting accessories

Since use of a dull accessory, such as a bull point, a

cutter, etc. will degrade eﬃ ciency and cause possible

motor malfunction, sharpen or replace with a new one as

soon as abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes (Fig. 8)

The Motor employs carbon brushes which are

consumable parts. When they become worn to or near

the “wear limit” ⓐ, it results in motor trouble.

When an auto-stop carbon brush is equipped, the motor

will stop automatically. At that time, replace both carbon

brushes with new ones which have the same carbon

brush Numbers ⓑ shown in the Fig. 8. In addition,

always keep carbon brushes clean and ensure that they

slide freely within the brush holders.

5. Replacing carbon brushes

Loosen the set screw and remove the tail cover. Remove

the brush caps and carbon brushes. After replacing the

carbon brushes, do not forget to tighten the brush caps

securely and to install the tail cover.

6. Replacing supply cord

If the replacement of the supply cord is necessary, it

has to be done by HiKOKI Authorized Service Center to

avoid a safety hazard.

000BookH60MC.indb8000BookH60MC.indb8 2022/10/3117:05:122022/10/3117:05:12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi H60MC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hitachi H60MC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info