Bedienungsanleitung Hitachi M 12 V 2 (Seite 11 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

78987

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

English

between the radius of the template guide and the

radius of the bit. The reverse is true when using

the router along the exterior of the template.

(3) Straight guide

Use straight guide for chamfering and groove cutting

along the materials side.

1 Insert the guide bar into the hole in the bar holder,

then lightly tighten the 2 wing bolts (A) on top of

the bar holder.

2 Insert the guide bar into the hole in the base, then

firmly tighten the wing bolt (A).

3 Make minute adjustments of the dimensions between

the bit and the guide surface with the feed screw,

then firmly tighten the 2 wing bolts (A) on top of

the bar holder and the wing bolt (B) that secures

the straight guide.

4 As shown in Fig. 14, securely attach the bottom of

the base to processed surface of the materials. Feed

the router while keeping the guide plane on the

surface of the materials.

(4) Dust guide and Dust guide adapter (Fig. 15)

Your router is equipped with dust guide and a dust

guide adapter.

1 Match the 2 grooves on the base and insert the

2 dust guide tabs in holes located in the base side

from the top. Tighten the dust guide with a screw.

The dust guide diverts cutting debris away from the

operator and directs the discharge in a consistent

direction.

2 By fitting the dust guide adapter into the dust guide

cutting debris discharge vent, the dust extractor can

be attached.

4. Adjusting the rotation speed (Model M12V2 only)

The M12V2 has an electronic control system that

allows stepless rpm changes.

As shown in Fig. 16, dial position “1” is for minimum

speed, and position “6” for maximum speed.

5. Removing the spring

The springs within the column of the router can

be removed. Doing so will eliminate spring

resistance and allows easy adjustment of cutting

depth when attaching the router stand.

(1) Loosen the 4 sub base screws, and remove the sub

base.

(2) Loosen the stopper bolt and remove it, so the

spring can be removed. (Fig. 17)

CAUTION

Remove the stopper bolt with the main unit (router)

fixed at its maximum height.

Removing the stopper bolt with the unit in a

shortened condition may cause the stopper bolt and

spring to be discharged and cause injury.

6. Cutting

CAUTION

⅜ Wear eye protection when operating this tool.

⅜ Keep your hands, face and other body parts away

from the bits and any other rotating parts, while

operating the tool.

(1) As shown in Fig. 18, remove the bit from the work

pieces and press the switch lever up to the ON

position. Do not start cutting operation until the bit

has reached full rotating speed.

(2) The bit rotates clockwise (arrow direction indicated

on the base). To obtain maximum cutting

effectiveness, feed the router in conformance with

the feed directions shown in Fig. 19.

NOTE

If a worn bit is used to make deep grooves, a high

pitched cutting noise may be produced.

Replacing the worn bit with a new one will eliminate

the high pitched noise.

USING THE OPTIONAL ACCESSORIES

Trimmer Guide (Fig. 20):

Use the trimmer guide for trimming or chamfering.

Attach the trimmer guide to the bar holder as

shown in Fig. 21.

After aligning the roller to the appropriate position,

tighten the two wing bolts (A) and the other two

wing bolts (B). Use as shown in Fig. 22.

MAINTENANCE AND INSPECTION

1. Oiling

To ensure smooth vertical movement of the router,

occasionally apply a few drops of machine oil to

the sliding portions of the columns and end bracket.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes

For your continued safety and electrical shock

protection, carbon brush inspection and replacement

on this tool should ONLY be performed by a HITACHI

AUTHORIZED SERVICE CENTER.

5. Replacing supply cord

If the supply cord of Tool is damaged, the Tool

must be returned to Hitachi Authorized Service

Center for the cord to be replaced.

6. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed in

each country must be observed.

MODIFICATION

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

01Eng_M12V2_WE 8/18/11, 10:38 AM10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi M 12 V 2 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info