Bedienungsanleitung Hitachi M 6 SB (Seite 7 von 38) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

78986

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

English

SPECIFICATIONS

*Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Trimmer guide ass'y ................................................ 1

(2) Straight Guide ........................................................... 1

(3) Template Guide (with two M4 screws) ................ 1

(4) Wrench 17/19 mm .................................................... 1

Standard accessories are subject to change without

notice.

APPLICATIONS

⅜

Plywood trimming

⅜ Various beveling

⅜ Various grooving

⅜ Engraving

⅜ Cut offs

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements specified on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position.

If the plug is connected to a receptacle while the

power switch is in the ON position, the power tool

will start operating immediately, which could cause

a serious accident.

3. Extension cord

When the work area is removed from the power

source, use an extension cord of sufficient thickness

and rated capacity. The extension cord should be

kept as short as practicable.

4. Fitting the bit

Refer to "Fitting and removal of the bit" section

given in the following. It is dangerous if the bit is

not fitted to the coIlet chuck securely. Check if the

collet chuck is sufficiently tightened.

5. Cutting using the workpiece edge as a base line

(Fig. 1)

Note that the distance between the machine center

and the hollow differs from the other three distances.

6. Confirm the spindle lock mechanism.

Confirm that the spindle lock is disengaged by

pushing the push button two or three times before

switching the power tool on. (See Fig. 2)

FITTING AND REMOVAL OF THE BIT

1. Fitting the bit

(1) Remove the base ass'y from the body. When

loosening the wing nut (See Fig. 3), the base ass'y

can be removed.

(2) Deeply inset the bit into the collet chuck hole. (The

distance is 15 mm or more from side of collet

chuck.)

(3) Depress spindle lock (Fig. 2) and rotate collet nut

clockwise by hand until lock engages hole in motor

spindle.

(4) While holding spindle lock engaged, tighten collet

nut securely by turning clockwise using wrench

provided.

CAUTIONS

⅜ Make sure to tighten the collet chuck after inserting

the bit. Collet chuck may be damaged if it is tightened

without inserting the bit.

⅜ Avoid depressing the lock pin while the bit is still

in rotation. Because, there is a fear that doing so

may result in an abnormal noise or damage in the

fixed section of the rotating shaft.

(5) Fit the removed base assembly to the rack provided

on the body's outer housing after adjusting the

pinion of the base assembly thereto. Then tighten

the wing nut and fix the assembly securely.

2. Removal of the bit

Loosen the collet chuck in the reverse manner as

described for the fitting the bit.

CAUTION

Bit is heated after the cutting work.

Do not touch it directly.

Voltage (by areas)* (110V, 230V, 240V)

Power Input* 440 W

No-load speed 30000 min

-1

Collet Chuck Capacity 6 mm or 6.35 mm (1/4")

Weight (Only main body) 1.4 kg

PRECAUTIONS ON USING TRIMMER

1. Always use the bit of correct shank diameter suitable

for the speed of the tool.

2. Hold the body firmly during operation. Otherwise,

injuries can result.

3. The bit is very hot immediately after operation.

Avoid bare hand contact with the bit for any reason.

4. Avoid bringing your hand, face, etc., close to the

bit and rotary parts during operation.

5. Exercise caution as the bit remains rotating even

after the switch is turned off. Contact of your hand,

etc., with the rotating bit can result in injuries.

01Eng_M6SB_WE 5/14/07, 17:186

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi M 6 SB Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info