Bedienungsanleitung Hitachi M 8 SA 2 (Seite 10 von 54) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

78984

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

English

(1) As shown in Fig. 12, remove the bit from the work

pieces and press the switch lever up to the ON

position. Do not start cutting operation until the bit

has reached full rotating speed.

(2) The bit rotates clockwise (arrow direction indicated

on the base). To obtain maximum cutting

effectiveness, feed the router in conformance with

the feed directions shown in Fig. 13.

NOTE

If a worn bit is used to make deep grooves, a high

pitched cutting noise may be produced.

Replacing the worn bit with a new one will eliminate

the high pitched noise.

USING THE OPTIONAL ACCESSORIES

(1) Trimmer Guide (Fig. 14):

Use the trimmer guide for trimming or chamfering.

Attach the trimmer guide to the bar holder as

shown in Fig. 15.

After aligning the roller to the appropriate position,

tighten the two wing bolts (A) and the other two

wing bolts (B). Use as shown in Fig. 16.

(2) Dust collector set (Fig. 17)

Connect the dust collector set cleaner to collect

dust.

For installation methods, please refer to the handling

instructions that came with the set.

(3) Fine adjustment knob (Fig. 17)

Connect the fine adjustment knob to adjust the

depth of cut finely.

For installation methods, please refer to the handling

instructions that came with the set.

MAINTENANCE AND INSPECTION

1. Oiling

To ensure smooth vertical movement of the router,

occasionally apply a few drops of machine oil to

the sliding portions of the columns and end bracket.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes

For your continued safety and electrical shock

protection, carbon brush inspection and replacement

on this tool should ONLY be performed by a HITACHI

AUTHORIZED SERVICE CENTER.

5. Replacing supply cord

If the supply cord of Tool is damaged, the Tool

must be returned to Hitachi Authorized Service

Center for the cord to be replaced.

6. Service parts list

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed in

each country must be observed.

MODIFICATION

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without

prior notice.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country specific regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling

instruction, to a Hitachi Authorized Service Center.

NOTE

Due to HITACHI’s continuing program of research and

development, the specifications herein are subject to

change without prior notice.

IMPORTANT

Correct connection of the plug

The wires of the main lead are coloured in accordance

with the following code:

Blue: – Neutral

Brown: – Live

As the colours of the wires in the main lead of this tool

may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black.

The wire coloured brown must be connected to the

terminal marked with the letter L or coloured red.

Neither core must be connected to the earth terminal.

NOTE

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except The United Kingdom.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi M 8 SA 2 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info