Bedienungsanleitung Hitachi m 8 (Seite 30 von 34) (Englisch, Dänisch, Schwedisch, Norwegisch, Finnisch)

427018

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

English

10)

and secure straight guide. As shown in Fig. 10,

securely attach the bottom of the base to the processed

surface of the materials. Feed the router while keeping

the guide plane on the surface of the materials.

(2) Parallel Guide (Model M8V(S), M8(S)):

Use the parallel guide for chamfering and groove

cutting along the materials side. First of all, as shown

in Fig. 10, attach the two wing bolts (A) (M6 × 15)

and

the two lock springs

(both standard accessories) to

the screw holes on the top side of the base. Insert the

guide bar

in the hole on the base and adjust the

distance from the bit to the guide plane

. Tighten the

two wing bolts (A) (M6 × 15)

to secure the parallel

guide

As shown in Fig. 11, securely attach the bottom of the

base to the processed surface of the materials. Feed

the router while keeping the guide plane on the surface

of the materials.

(3) Template Guide:

Use the template guide when employing a template

for producing a large quantity of identically shaped

products.

As shown in Fig. 12, secure the template guide

the base of the router with two accessory screws. At

this time, ensure that the projection side of the template

guide

is facing the bottom surface of the base of the

router.

A template is a profiling mold made of plywood or thin

lumber. When making a template, pay particular

attention to the matters described below and illustrated

in Fig. 13.

When using the router along the interior plane of the

template

, the dimensions of the finished product

will be less than the dimensions of the template

, by

an amount equal to dimension “A”, the difference

between the radius of the template guide

and the

radius of the bit

. The reverse is true when using the

router along the exterior of the template

Secure the template to the workpiece. Feed the router

in the manner that the template guide moves along

the template as shown in Fig. 14.

3. Adjusting the rotating speed (Model M12V(S), M8V(S)

only)

Model M12V(S) and M8V(S) have an electronic control

system that allows stepless rpm changes.

As shown in Fig. 15, dial

position “1” is for minimun

speed and position “5” for maximum speed.

4. Cutting

(1) As shown in Fig. 16, remove the bit from the work

pieces and press the switch lever up to the ON position.

Do not start cutting operation until the bit has reached

full rotating speed.

(2) The bit rotates clockwise (arrow direction indicated on

the base). To obtain maximum cutting effectiveness,

feed the router in conformance with the feed directions

shown in Fig. 17.

USING THE OPTIONAL ACCESSORIES

1. Model M12V(S), M12SA(S)

(1) Trimmer Guide (Fig. 18

Use the trimmer guide for trimming or chamfering.

Attach the trimmer guide

to the bar holder

shown in Fig. 19. After aligning the roller

to the

appropriate position, tighten the two wing bolts (A)

and the other two wing bolts (C)

. Use as shown in

Fig. 20.

2. Model M8V(S), M8(S)

(1) Trimmer Guide (Fig. 21

)

Use the trimmer guide for trimming, chamfering or

working the inner surface. Attach the trimmer guide

to the base as shown in Fig. 22. After aligning the roller

to the appropriate position, tighten the two wing

bolts (A)

and the other wing bolt (C)

. Use as

shown in Fig. 22.

(2) Feed screw ass'y (Fig. 21

)

The feed screw assembly can be used to make fine

adjustments in the distance between the bit and the

parallel guide or trimmer guide. Attach the feed screw

to the parallel guide

or the trimmer guide as

shown in Fig. 24 and then attach the rod

to the base

using the nuts provided. Turn the feed screw

make fine adjustments. Push the button on the feed

screw

to release the grip of the screw and allow fast

movement of the guide.

3. Model M12V(S), M12SA(S), M8V(S), M8(S)

(1) Dust collector Set (Fig. 27

)

Connect the dust collector set (Fig. 27

) cleaner to

collect dust.

MAINTENANCE AND INSPECTION

1. Adjusting the lock lever position:

The lock lever part is provided with a brass lock piece

to protect the column. When the lock piece becomes

excessively worn, the lock position of the lock lever

tends to drop. Should router operation and handling

become difficult as a result, remove the E-type retaining

ring and adjust the setting position of the dodecagonal

hole on the lock lever and the hexagonal axis of the

lock screw, as shown in Fig. 25.

2. Oiling:

To ensure smooth vertical movement of the router,

occasionally apply a few drops of machine oil to the

sliding portions of the columns and end bracket.

3. Inspecting the mounting screws:

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws

be loose, retighten them immediately. Failure to do so

could result in serious hazard.

4. Inspecting the carbon brushes: (Fig. 26)

The motor employs carbon brushes which are

consumable parts. Since an excessively worn carbon

brush could sesult in motor trouble, replace a carbon

brush with a new one having the same carbon brush

No. shown in the figure when it becomes worn to or

near the “wear limit”

in addition, always keep

carbon brushes clean and ensure that they slide freely

within the brush holders.

⅜ Replacing a carbon brush:

Disassemble the brush cap with a minus-head

screwdriver. The carbon brush can then be easily

removed.

5. Maintenance of the moter:

The motor unit winding is the very “heart” of the

power tool. Exercise due care to ensure the winding

does not become damaged and/or wet with oil or

water.

Hitachi m 8 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info