Bedienungsanleitung Hitachi M12SE (Seite 9 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

511994

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

English

4. Setting the attachment angle of the handle

As Fig. 1 shows, the handle attachment angle can

be set in three stages. Use a plus head screwdriver

to loosen the machine screw attached to the handle,

adjust the handle to the desired position and

retighten the machine screw.

INSTALLING AND REMOVING BITS

WARNING

Be sure to switch power OFF and disconnect the

plug from the receptacle to avoid serious trouble.

1. Installing bits

(1) Clean and insert shank of bit into the collet chuck

until shank bottoms, then back it out approximately

2 mm.

(2) With the bit inserted and pressing the lock pin

holding the armature shaft, use the 23 mm wrench

to firmly tighten the collet chunk in a clockwise

direction (viewed from under the router). (Fig. 2)

CAUTION

⅜ Ensure that the collet chuck is firmly tightened after

inserting a bit. Failure to do so will result in damage

to the collet chuck.

⅜ Ensure that the lock pin is not inserted into the

armature shaft after tightening the collet chuck.

Failure to do so will result in damage to the collet

chuck, lock pin and armature shaft.

(3) When using the 8 mm or 1/4" diameter shank bit,

replace the equipped collet chuck with the one for

8 mm or 1/4" diameter shank bit which is provided

as the optional accessory.

2. Removing Bits

When removing the bits, do so by following the

steps for installing bits in reverse order.

CAUTION

Ensure that the lock pin is not inserted into the

armature shaft after tightening the collet chuck.

Failure to do so will result in damage to the collet

chuck, lock pin and armature shaft.

HOW TO USE THE ROUTER

1. Adjusting depth of cut (Fig. 3)

(1) Use stopper pole to adjust depth of cut.

1 Place the tool on a flat wood surface.

2 Turn the stopper block so that section to which the

cutting depth setting screw on a stopper block is

not attached comes to the bottom of the stopper

pole. Loosen wing bolt allowing the stopper pole

to contact with stopper block.

3 Loosen the lock lever and press the tool body until

the bit just touches the flat surface. Tighten the lock

lever at this point. (Fig. 4)

4 Tighten wing bolt. Align the depth indicator with

the “0” graduation of scale.

5 Loosen wing bolt, and raise until indicator aligns

with the graduation representing the desired cutting

depth. Tighten wing bolt.

6 Loosen the lock lever and press the tool body down

until the stopper block to obtain the desired cutting

depth.

(2) As shown in Fig. 5 (a), loosening the two nuts on

the threaded column and moving then down will

allow you to move down to the end position of the

bit when the lock lever is loosened. This is helpful

when moving the router to align the bit with the

cutting position.

As shown in Fig. 5 (b), tighten the upper and lower

nuts to secure the cutting depth.

(3) When you are not using the scale to set the cutting

depth, push up the stopper pole so that it is not

in the way.

2. Stopper block (Fig. 6)

The 2 cut-depth setting screws attached to the

stopper block can be adjusted to simultaneously set

3 different cutting depth. Use a wrench to tighten

the nuts so that the cut-depth setting screws do not

come loose at this time.

3. Guiding the router

WARNING

Be sure to switch power OFF and disconnect the

plug from the receptacle to avoid serious trouble.

(1) Template Guide

Use the template guide when employing a template

for producing a large quantity of identifically shaped

products.

As shown in Fig. 7, secure the template guide to

the base of the router with two accessory screws.

At this time, ensure that the projection side of the

template guide is facing the bottom surface of the

base of the router.

A template is a profiling mold made of plywood

or thin lumber.

When making a template, pay particular attention

to the matters described bellow and illustrated in

Fig. 8.

When using the router along the interior plane of

the template, the dimensions of the finished product

will be less than the dimensions of the template

by a amount equal to dimension “A”, the difference

between the radius of the template guide and the

radius of the bit. The reverse is true when using

the router along the exterior of the template.

Secure the template to the workpiece. Feed the

router in the manner that the template guide moves

along the template as shown in Fig. 9.

(2) Parallel guide (Fig. 10)

Use parallel guide for chamfering and groove cutting

along the materials side.

1 Insert the guide bar into the hole in the base, adjust

the distance between the bit and the guide surface,

and then firmly tighten the wing bolt (A).

2 As shown in Fig. 11, securely attach the bottom of

the base to processed surface of the materials. Feed

the router while keeping the guide plane on the

surface of the materials.

4. Adjusting the rotation speed (Model M12VE only)

The M12VE has an electronic control system that

allows stepless rpm changes.

As shown in Fig. 12, dial position “1” is for minimum

speed, and position “6” for maximum speed.

5. Cutting

CAUTION

⅜ Wear eye protection when operating this tool.

⅜ Keep your hands, face and other body parts away

from the bits and any other rotating parts, while

operating the tool.

01Eng_M12VE_WE 4/6/10, 14:258

Hitachi M12SE Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info