Bedienungsanleitung Hitachi N5008AC (Seite 8 von 42) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

568867

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

English

STAPLE SELECTION

Choose a suitable staple from Fig. Staples which are not

shown in Fig. can not be driven with this tool.

Dimension of staples

STANDARD ACCESSORIES

(1) Hexagon bar wrench for M5 screw........................... 1

(2) Eye protection............................................................. 1

(3) Oiler ............................................................................. 1

OPTIONAL ACCESSORY

⅜ Sequential Trip Mechanism Kit (Code No.876762)

(Sequential Fire Parts Set, Single Shot Parts)

With the sequential fire parts, the staple is driven

only by squeezing the trigger after pushing down

the push lever.

By installing these parts, driving staples into

improper positions and unexpected firing of staples

caused by accidental operation of the push lever can

be prevented.

APPLICATIONS

⅜ Construction work such as wall sheathing, roof

decking, subflooring.

⅜ Mobile and modular home construction.

⅜ Making wooden boxes, palletes, and drums.

PREPARATION PRIOR TO OPERATION

1. Prepare the hose

Be sure to use the hose provided with minimum

6 mm (1/4”) inside diameter.

NOTE:

The air supply hoses must have a minimum working

pressure rating of 12.8 bar (180 psi) or 150 percent of

the maximum pressure produced in the air supply

system, whichever is higher.

2. Check on safety

CAUTIONS:

⅜ Unauthorized persons (including children) must be

kept away from the equipment.

⅜ Wear eye protection.

⅜ Check the retaining screws which fix the exhaust

cover, etc. for tightness.

Check the stapler for air leaks and defective or rusty

parts.

⅜ Check whether or not the push lever works correctly.

Also check whether or not any dirt has adhered to the

moving parts of the push lever.

⅜ Recheck on operational safety.

BEFORE USE

1. Check the air pressure

CAUTION:

The air pressure must be constantly maintained at 4.9

– 8.3 bar (70 – 120 psi.).

Adjust the air pressure between 4.9 to 8.3 bar (70 –

120 psi.) according to the diameters and length of

staples and hardness of the wood being stapled. Pay

special attention to the output pressure, capacity, and

piping on the air compressor, so that air pressure does

not exceed the specified limit. Note that excessive

pressure may affect overall performance, service life,

and safety.

2. Lubrication

(1) Prior to operating this stapler, be sure to provide an

air set between the air compressor and this device.

Lubrication through the air set offers smooth

operation, extended service life, and anticorrosion.

Adjust the oiler so that a single drop of oil is supplied

at intervals of 5 to 10 stapling cycles.

Type of power Piston reciprocating

Air pressure (Gauge) 4.9 – 8.3 bar (70 – 120 psi.)

Applicable staples ref. Fig.

Amount of loadable staples 150 staples

Size 365 mm (L) × 254 mm (H) × 76 mm (W) (14-3/8” × 10” × 3”)

Weight 2.0 kg (4.4 lbs)

Hose (inside diam.) 6 mm (1/4”)

SPECIFICATIONS

16 Gauge 7/16" Crown

Min. Max.

1.45mm

(.057")

7.9mm

(.309")

1.61mm

(.063")

25mm (1")

50mm (2")

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi N5008AC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info