Bedienungsanleitung Hitachi NR90GC2 (Seite 8 von 90) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

568887

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

English

27. Do not use a transformer containing a booster.

28. Do not charge the battery from an engine electric

generator or DC power supply.

29. Always charge indoors.

Because the charger and battery heat slightly during

charging, charge the battery in a place not exposed

to direct sunlight; where the humidity is low and

the ventilation is good.

30. The exploded assembly drawing on this handling

instructions should be used only for authorized

service center.

PRECAUTIONS ON USING GAS STRIP NAILER

1. Safe operation through correct usage.

This tool was designed for driving nails into wood and

similar materials. Use it for its intended purpose only.

2. Be careful of ignition and explosions.

This tool must not be used in a

combustible environment or in

presence of flammable liquids or

gases. This tool produces hot exhaust

gases that may ignite flammable

materials and produces sparks. Since sparks may fly

during nailing, it is dangerous to use this tool near

lacquer, paint, benzine, thinner, gasoline, gas,

adhesives and similar inflammable substances as they

may ignite or explode. Under no circumstances should

this tool therefore be used in the vicinity of such

inflammable material.

3. Explosion and fire hazard.

The fuel cell is an aerosol dispensers

with flammable contents.

Pressured container and the

propellant will remain in the fuel cell.

Failure to follow instructions may

result in explosion or fire.

Keep the power tool, fuel cells and

battery away from sunshine and from

temperature exceeding 50°C (120°F).

Fuel cell and/or battery may burst,

releasing flammable gas.

Do not pierce or burn the container,

even after use.

Do not incinerate, refill, reclaim or

recycle the fuel cell.

Do not spray to a naked flame or

any incandescent material.

Keep away from ignition sources – No smoking.

Keep out of the reach of children.

4. Always wear eye protection (protective goggles).

When operating the power tool,

always wear eye protection, and

ensure that surrounding people wear

eye protection too.

The possibility of fragments of the nails

that were not properly hit entering the

eye is a threat to sight. Eye protection can be bought

at any hardware store. Always wear eye protection

while operating this tool. Use either eye protection

or a wide vision mask over prescription glasses.

Employers should always enforce the use of eye

protection equipment.

5. Protect your ears and head.

When engaged in nailing work please wear ear

mufflers and head protection. Also, depending on

condition, ensure that surrounding people also wear

ear mufflers and head protection.

6. Use outside or well-ventilated areas.

This tool exhausts carbon monoxide

which are a danger to health when

inhaled.

This tool shall not be used in

enclosed or poorly ventilated areas.

Do not inhale.

7. Pay attention to those working close to you.

It would be very dangerous if nails that were not

properly driven in should hit other people.

Therefore, always pay attention to the safety of the

people around you when using this tool. Always

make sure that nobody’s body, hands or feet are

close to the nail outlet.

8. Never point the nail outlet towards people.

Always assume the tool contains

fasteners.

If the nail outlet is pointed towards

people, serious accidents may be

caused if you mistakenly discharge

the tool. When connecting and disconnecting the

battery or fuel cell, during nail loading or similar

operations, be sure the nail outlet is not pointed towards

anyone (including yourself). Even when no nails are

loaded at all, it is dangerous to discharge the tool while

pointing it at someone, so never attempt to do so. No

horseplay. Respect the tool as a working implement.

9. Before using the power tool, check the push lever.

The Push Lever and Chamber operate in conjunction

for this device.

Before using the power tool make sure to check that

the push lever operate properly. Without nails,

fuel cell and battery loaded into the power tool,

check the following.

If abnormal operation occurs, do not use the power

tool until it has been inspected and repaired.

⅜ Pull the Feeder knob with the device facing

upward and press down the Push lever then

confirm that the Push lever securely returns to

its original position.

The Push lever operation becomes especially

heavy in low temperatures and drive operations

may not function.

⅜ With pulling back the feeder knob, the push lever

must move smoothly.

⅜ With pulling back the feeder knob, the trigger

must move smoothly.

Furthermore, with regard to the push lever, please

note that it must never be modified or removed.

10. Use specified nails only.

Never use nails other than those specified and

described in these instructions.

11. Be careful when connecting the battery.

When connecting the battery and loading nails in

order not to fire the tool by mistake, make sure of

the followings.

⅜ Do not touch the trigger.

⅜ Do not allow the firing head to contact with any

surface.

MAX 50°C

(120°F)

01Eng_NR90GC2_WE_7L 4/14/08, 8:11 PM7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NR90GC2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info