Bedienungsanleitung Hitachi NR90GC2 (Seite 12 von 90) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

568887

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

English

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the battery

and recharge it after it has cooled for a while.

PREPARATION PRIOR TO OPERATION

CAUTIONS

⅜ No flammable gas, liquid or other flammable objects

at worksite.

⅜ Use outside or well–ventilated areas.

Do not inhale.

⅜ Keep the tool, fuel cell and battery away from sunshine

and from temperature exceeding 50°C (120°F).

⅜ Keep away from ignition sources. No smoking.

⅜ Clear the area of children or unauthorized personnel.

⅜ Do not store the tool, fuel cell and battery in a cold

weather environment. Keep the tool, fuel cell and

battery in a warm area until beginning the work.

⅜ If the tool, fuel cell and battery are already cold, bring

it in a warm area and allow the tool to warm up before

use.

Observe temperature limit of max. 50°C (120°F).

Do not expose to an open flame and sparks!

⅜ This tool may not drive completely below when;

– at low temperature fuel cell loose the required

propellant force,

– at high temperature fuel cell overdose.

⅜ Do not use the tool in the rain or where excessive

moisture is present.

⅜ This tool is not recommended for use at altitudes

above 1,500 m (5000 feet), or in temperature below

0°C (30°F).

1. Fuel cell

To attach the metering valve to a fuel cell:

(1) Separate the metering valve and the cap from the gas

cartridge (See Fig. 3 (1)).

(2) Press forward (stem side) and downward on the front

side of the metering valve (See Fig. 3 (2)).

(3) Press downward on the rear of the metering valve

until it seals (See Fig. 3 (3)).

Check the metering valve:

Press the metering valve stem on fuel cell two or three

times against a stationary object and release.

If gas is not dispersed, fuel cell is empty. Replace it.

Observe Safety Regulations

CAUTION

⅜ If the gas leaks from the metering valve or the gas

cartridge after attached the metering valve, replace

with the new metering valve.

⅜ Do not attempt to reuse the metering valve.

Replace with the new metering valve.

2. Battery

You must charge the battery before use.

The charging method of battery is shown in page 10.

3. Check on safety

CAUTIONS

⅜ Unauthorized persons (including children) must be

kept away from the equipment.

⅜ Wear eye protector.

⅜ Check the retaining screws which fix the top cover,

etc. for tightness.

Check the tool for defective or rusty parts.

⅜ Check whether or not the push lever works correctly

without nails, fuel cell and battery. Also check whether

or not any dirt has adhered to the moving parts of the

push lever.

⅜ Recheck on operational safety.

BEFORE USE

1. Insert battery into the tool (See Fig. 4)

Do not operate the push lever or trigger while

installing the battery.

Make sure the battery indicator light is flashing GREEN

(See Fig. 5).

If the battery indicator light is flashing RED, the battery

doesn’t have enough power and it needs to be

charged.

BATTERY INDICATOR LIGHT

– Flashing GREEN: Enough power remaining (The

light turns steady during

operation).

– Flashing RED: Insufficient power remaining (The

light turns steady during operation).

–OFF: The battery is extremely empty. Charge the

battery.

Power saving mode

If the tool has not been used for about an one hour

with the battery still installed, Power saving mode

turns on to minimize unnecessary consumption of

battery power. Power saving mode is also activated

when the battery power is extremely low or there’s

an abnormality in the machine so please pay attention

to the battery indicator light after deactivating Power

saving mode (by removing the battery and reinstall

it).

2. Insert fuel cell into the tool

(1) Pulling the latch and open the cell cover (See Fig. 6).

(2) Insert the fuel cell into the tool (See Fig. 7).

(3) Insert the stem of fuel cell into the hole of adaptor

(See Fig. 8).

(4) Close the cell cover.

3. Load nails

(1) Insert nail strip into rear of magazine (See Fig. 9).

(2) Slide the nail strip forward in the magazine (See Fig. 10).

(3) Pull the nail feeder (B) back to engage the feeder knob

to the nail strip (See Fig. 11).

NOTE

⅜ Use nail strip of more than 10 nails.

The Nailer is now ready to operate.

Removing the nails:

1 Pull the feeder knob backward (See Fig. 12).

2 Return the feeder knob forward quietly while pushing

the nail feeder (B).

3 Pull out nails from the back of the magazine (See Fig.

13).

01Eng_NR90GC2_WE_7L 4/14/08, 8:11 PM11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NR90GC2 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info