Bedienungsanleitung Hitachi NT65A2 (Seite 5 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

568891

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

English

(3) After inserting the nails, pull the nail feeder up in

backward direction, remove it from the roll pin, move

it slowly forward and push the nail.

NOTE:

After having removed the nail feeder from the roll pin

and moving it forcefully forward, the nail coupling

may brake and the nail feeder may get caught between

the magazine and nails, causing poor nail feeding.

Therefore, move the nail feeder slowly forward.

CAUTIONS

⅜ To prevent unintentional operation, never touch the

trigger or place the top end of the push lever on a work

bench on floor. Also, never face the nail outlet toward

any part of a person.

⅜ Use nails in which five nails are connected.

HOW TO USE THE NAILER

CAUTIONS

⅜ Never use the head or body of this device as a hammer.

⅜ Take precautions to ensure the safety of persons in the

vicinity during operation.

1. Nailing procedures

(1) Intermittent nailing

Depress the nail outlet onto the desired point; then

pull the trigger to drive a nail in a single shot. (See Fig.

Fig. 3

CAUTION

This tool will sometimes fire twice in rapid succession

when strongly pressed flush against a surface or

when using on hard materials. In such cases, fire the

nails by squeezing and quickly releasing the trigger.

(2) Push lever

When depressing the nail outlet, be sure to fully lift the

push lever (See Fig. 3) to release the safety lock. Thus,

nails cannot be driven without releasing the safety

lock even though the trigger is pulled.

(3) Continuous nailing

First, pull the trigger. Then depress the devise onto the

desired position to automatically drive nails. (See Fig.

4).

Fig. 4

CAUTION

Excercise care when nailing corners of lumber. When

continuous nailing corners of lumber, a nail may go

astray or break through the corner.

NOTES

⅜ Precautions on no-load operation

Sometimes nailing will continue after driving in all

nails previously contained in the magazine.

This is termed “no-load operation”. Such operation

may deteriorate the damper, magazine, and nail feeder.

To avoid no-load operation, occasionally confirm the

amount of remaining nails. On the other hand, all nails

should be removed after using this nailer.

⅜ After completing operation, put into the body about

2cc oil through the hose joint to protect the tool from

rust.

⅜ Under low temperature conditions, the machine

sometimes does not operate correctly. Always operate

the machine at the appropriate ambient temperature.

2. Attachment and detachment of the nose cap

CAUTIONS:

⅜ When attaching and detaching the nose cap, make

sure to disconnect the hose to release the compressed

air.

⅜ When attaching and detaching the nose cap, make

sure to take your finger off the trigger.

When you do not want to cause scratches in the material

you work with, use the accessory rubber nose cap. To

attach the nose cap, attach it as shown in Fig. 5. Detachment

shall be made in reversed order. Also, when attaching the

nose cap, the drive bit projection of the nail outlet will be

reduced and the nailing power will be lowered. Adjust the

nailing power according the air pressure used and the

attachment position of the bit guide.

Fig. 5

Push Lever Trigger

Previously pull the trigger.

Nose Cap

Disconnect air hose

Push Lever

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NT65A2 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info