Bedienungsanleitung Hitachi NT65GB (Seite 15 von 104) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

568894

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

English

⅜ Use nail strip of more than 5 nails.

The Nailer is now ready to operate.

Removing the nails:

1 Lightly press the stop lever and gently pull out the

magazine cover.

2 Remove the nails from the nailer.

CAUTION

⅜ To prevent unintentional operation, never touch the

trigger or place the top end of the push lever on a

work bench on floor. Also, never face the nail outlet

toward any part of a person.

HOW TO USE THE NAILER

CAUTION

⅜ Never use the top cover or housing of this device as a

hammer.

⅜ Take precautions to ensure the safety of persons in

the vicinity during operation.

⅜ Squeeze the push lever when drive a nail, otherwise

the piston can not return correctly.

⅜ Make sure the nailing depth when the temperature is

above 40°C or below 0°C.

⅜ Using the tool for an extended period may lead to oil

around the exhaust outlet or nose, resulting in

spattering.

To ensure that the material to be nailed stays clean,

wipe off any oil that gets on the tool.

1. Nailing procedures

This power tool is equipped with a FULL SEQUENTIAL

ACTUATION MECHANISM.

(1) Intermittent nailing

Depress the nail outlet onto the desired point; then pull

the trigger to drive a nail in a single shot (See Fig. 18).

After nailing once, nailing will not be possible again

until the trigger is released and pressed again.

(2) Push lever

When depressing the nail outlet, be sure to fully lift

the push lever (See Fig. 18) to release the safety lock.

Thus, nails cannot be driven without releasing the

safety lock even though the trigger is pulled.

NT65GS, NT65GB employs a preventive mechanism

for unloaded operation.

NT65GS, NT65GB enters a state where the push lever

cannot be pushed up. This takes place when the

magazine is not loaded with nails or when the

remaining number of nails becomes less than 6 or 9 .

CAUTION

⅜ Exercise care when nailing corners of lumber. When

continuous nailing corners of lumber, a nail may go

astray or break through the corner.

⅜ Do not drive a nail on another nail.

⅜ Do not drive a nail on metal parts.

⅜ Use caution not to throw the push lever tip onto wood

when the push lever cannot be pushed up.

NOTE

⅜ Under low temperature conditions, the tool

sometimes does not operate correctly. Always operate

the tool at the appropriate ambient temperature.

2. Adjusting the nailing depth

To assure that each nail penetrates to the same depth,

be sure that the tool is always held firmly against the

workpiece.

If nails are driven too deep or shallow into the

workpiece, adjust the nailing in the following order.

1 Remove the fuel cell and the battery from the

nailer. (See Fig. 19).

2 If nails are driven too deep, turn the adjuster to

the shallow side (See Fig. 20(a)).

Adjustments are in half-turn increments.

If nails are driven too shallow, turn the adjuster to

the deep side (See Fig. 20(b)).

3 Stop turning the adjuster when a suitable position

is reached for a nailing test.

4 Connect the fuel cell and the battery to the nailer.

ALWAYS WEAR EYE PROTECTOR.

Perform a nailing test.

5 Remove the fuel cell and the battery from the nailer.

6 Choose a suitable position for the adjuster.

3. Using the hook

The hook can be installed on the right or left side.

1 Securely hold the main unit and remove the screw

using a screwdriver (Fig. 21).

2 Remove the hook and hook plate (Fig. 22).

3 Install the hook on the other side and securely

fasten with screw (Fig. 23).

4. Using the nose cap (See Fig. 24, 25)

If you like to protect the surface of workpiece against

scratches or markings made by the push lever, attach

the accessory nose cap to the push lever.

(1) DISCONNECT BATTERY and FUEL CELL.

(2) Put in the nose cap in the direction of the arrow as

shown in the diagram.

(3) The nose cap is marked to indicate the exit point of

the nail, making alignment easier.

⅜ Pull out the tip of the push lever in the reverse order

of attachment.

When not using the nose cap, attach to the storage area

in back of the magazine. (See Fig. 26, 27)

INSPECTION AND MAINTENANCE

CAUTION

Be sure to remove the battery and fuel cell during

clearing jams, inspection, maintenance and cleaning.

1. Countermeasure for nail jamming

1 DISCONNECT BATTERY and FUEL CELL.

2 Remove all nails.

Magazine

Gap

Side guide

groove

Nail

Groove

01Eng_NT65GS_WE 12/3/08, 8:4514

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hitachi NT65GB Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info